manualshive.com logo in svg

Chrysler 2017 Pacifica, Owner'S Manual, Page: 404 / 828

Share
Download
Chrysler 2017 Pacifica Owner'S Manual Download Page 404

and/or expand the range of torque converter clutch
engagement. This is done to prevent transmission dam-
age due to overheating.

If the transmission becomes extremely hot, the

⬙

Transmis-

sion Temperature Warning Light

⬙

will illuminate, a warn-

ing message will appear in the EVIC/DID and the
transmission may operate differently until the transmis-
sion cools down.

During cold temperatures, transmission operation may
be modified depending on engine and transmission
temperature as well as vehicle speed. This feature im-
proves warm up time of the engine and transmission to
achieve maximum efficiency. Engagement of the torque
converter clutch, and shifts into 8th or 9th gear, are
inhibited until the transmission fluid is warm (refer to the
“Note” under “Torque Converter Clutch” in this section).
Normal operation will resume once the transmission
temperature has risen to a suitable level.

LOW (L)

Use this range for engine braking when descending very
steep grades. In this range, the transmission will down-
shift for increased engine braking. To access the LOW
position, push down on the gear selector and rotate it
fully clockwise.

Transmission Limp Home Mode

Transmission function is monitored electronically for
abnormal conditions. If a condition is detected that could
result in transmission damage, Transmission Limp Home
Mode is activated. In this mode, the transmission may
operate only in a fixed gear, or may remain in NEUTRAL.
The Malfunction Indicator Light (MIL) may be illumi-
nated. Limp Home Mode may allow the vehicle to be
driven to an authorized dealer for service without dam-
aging the transmission.

402

STARTING AND OPERATING

Summary of Contents for 2017 Pacifica





























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments