manualshive.com logo in svg

Chrysler 2017 Pacifica, Owner'S Manual, Page: 589 / 828

Share
Download
Chrysler 2017 Pacifica Owner'S Manual Download Page 589

WARNING!

(Continued)

reach of children. If swallowed, rinse mouth imme-
diately with plenty of water and drink plenty of
water. Do not induce vomiting! Consult a physician
immediately.

Sealing A Tire With Tire Service Kit

Whenever You Stop To Use Tire Service Kit:

1. Pull over to a safe location and turn on the vehicle’s

Hazard Warning flashers.

2. Verify that the valve stem (on the wheel with the

deflated tire) is in a position that is near to the ground.
This will allow the Tire Service Kit Hose to reach the
valve stem and keep the Tire Service Kit flat on the
ground. This will provide the best positioning of the
kit when injecting the sealant into the deflated tire and

running the air pump. Move the vehicle as necessary
to place the valve stem in this position before proceed-
ing.

3. Place the transmission in PARK and cycle the ignition

in the OFF position.

4. Set the parking brake.

Setting Up To Use Tire Service Kit:

1. Uncoil the Sealant Hose and then remove the cap from

the fitting at the end of the hose.

2. Place the Tire Service Kit flat on the ground next to the

deflated tire.

7

IN CASE OF EMERGENCY

587

Summary of Contents for 2017 Pacifica





























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments