Chrysler 2017 Pacifica Owner'S Manual Download Page 36 | Manualshive

Page: 36 / 828

Chrysler 2017 Pacifica Owner'S Manual Download Page 36

How To Use Remote Start

All of the following conditions must be met before the
engine will remote start:

•

Gear Selector in PARK

•

Doors closed

•

Hood closed

•

Liftgate closed

•

Hazard switch off

•

Brake switch inactive (brake pedal not pushed)

•

Battery at an acceptable charge level

•

RKE PANIC button not pushed

•

System not disabled from previous remote start event

•

Vehicle alarm system indicator flashing

•

Ignition in STOP/OFF position

•

Fuel level meets minimum requirement

WARNING!

•

Do not start or run an engine in a closed garage or
confined area. Exhaust gas contains Carbon Mon-
oxide (CO) which is odorless and colorless. Carbon
Monoxide is poisonous and can cause serious in-
jury or death when inhaled.

•

Keep Remote Keyless Entry (RKE) transmitters
away from children. Operation of the Remote Start
System, windows, door locks or other controls
could cause serious injury or death.

34

GETTING TO KNOW YOUR VEHICLE

«
...
34
35
36
37
38
...
»

Summary of Contents for 2017 Pacifica





























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments