Christ 102210 Operating Manual Download Page 36

Page: 36 / 126

Freeze-dryer Gamma 1-16 LSCplus

Freeze-dryer Gamma 2-16 LSCplus

4 Storage and transport

36 / 126

Version 04/2013, Rev. 2.10 of 09/03/2020

• sb-dc

Translation of the original operating manual

→

4.3

Notes on transport

• Use suitable packaging for the transport, and if at all possible, the

original packaging.

• Install all transport safety devices (see chapter 4.5 - "Transport safety

devices").

• Always lift the freeze-dryer with a lifting device.
• When lifting the freeze dryer, always reach under the freeze-dryer from

the side. Do not grab the unit at the plastic control panel.

CAUTION

The freeze-dryer

Gamma 1-16 LSCplus

weighs approx. 135 kg!

The freeze-dryer

Gamma 2-16 LSCplus

weighs approx. 160 kg!

CAUTION

The centre of gravity of the freeze-dryer is off-centre!

• When setting the unit down, ensure that the feet are upright (see figures

below).

correct

incorrect

Fig. 11: Unit feet

Summary of Contents for 102210































































































































Search results

Summary of Contents for 102210

Reviews:

Related manuals for 102210

Brands by name

Popular brands

Christ 102210, Operating Manual

Search results

Summary of Contents for 102210

Reviews:

Related manuals for 102210

Brands by name

Popular brands