Chint Power CPS SCH Series Installation And Operation Manual Download Page 111 | Manualshive

Page: 111 / 111

background image

107

Chapter 9 Limited Warranty

The warranty policy of this product is specified in the contract; otherwise, the

standard warranty is 5 years.

For service, Chint Power Systems America will provide local support. For

Warranty terms, please refer to the CPS America standard warranty policy in

place at time of purchase.

CHINT POWER SYSTEMS AMERICA CO., LTD.

Address:

700 International Parkway, Suite 102

Richardson Texas 75081

Service Hotline: 855-584-7168
Email: [email protected]
Website: www.chintpowersystems.com

SHANGHAI CHINT POWER SYSTEMS CO., LTD.

Headquarters: Building 4, No. 3255, Sixian Road,

Songjiang District, Shanghai, China

Tele: +86 -21 -3779 1222 -6300
Fax: +86 -21 -3779 1222 -6001

Part No:
This  manual  is  subject  to  change  without  prior  notification.  Copyright  is
reserved.  Duplication  of  any  part  of  this  issue  is  prohibited  without  written
permission.

«
...
109
110
111

Summary of Contents for CPS SCH Series
















































































































Reviews:

No comments

Related manuals for CPS SCH Series

Brand: Thinkpower Pages: 30

Brand: GME Pages: 21

Brand: Z3 Technology Pages: 15

Brand: Furrion net-zero Pages: 32

Brand: Paradox Pages: 2

Brand: Lika Pages: 2

Brand: Badger Meter Pages: 12

Brand: Baumer Pages: 36

ROTAPULS CK61 Series

Brand: Lika Pages: 2

Brand: Motrona Pages: 28

Brand: Spatz Pages: 22

Brand: Lindy Pages: 2

Brand: Larco Pages: 11

Brand: M2TECH Pages: 49

ETATRACK active

Brand: Lorentz Pages: 4

Brand: AEG Pages: 150

Brand: Seller Pages: 8

Brand: Whisper Power Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands