Chint Power CPS SCH Series Installation And Operation Manual Download Page 3

Page: 3 / 111

Table of Contents

Before You Start… .................................................................................. 1

Chapter 1 IMPORTANT SAFETY INSTRUCTIONS ................................ 2

Chapter 2 Overview ................................................................................ 6

2.1 Inverter for Grid-tied PV Systems .................................................. 6

2.2 Product Features ............................................................................. 6

2.3 Product Protection Functions .......................................................... 7

2.4 Smart Inverter Functions ................................................................ 7

2.5 Schematic Diagram and Circuit Design .......................................... 8

2.6 Appearance and Main Item Description.......................................... 9

2.7 Anti-islanding Detection ................................................................. 10

2.8 DC Ground Fault Protection ........................................................... 10

2.9 Surge Suppression .......................................................................... 10

Chapter 3 Installation ............................................................................. 11

3.1 Recommendations Before Installation ............................................ 13

3.2 Mechanical Installation ................................................................... 14

3.3 Electrical Installation ...................................................................... 29

Chapter 4 Commissioning (Via Wireless ) ............................................ 52

4.1 APP Download................................................................................ 52

4.2 Commissioning Checklist ............................................................... 52

4.3 Commissioning Steps ..................................................................... 53

4.4 Connection to the inverter – Wireless ............................................. 53

Chapter 5 APP Interface ......................................................................... 58

5.1 Overview ........................................................................................ 58

5.2 Main section ................................................................................... 59

5.3 Running Data .................................................................................. 60

5.4 Settings ........................................................................................... 61

5.5 History ............................................................................................ 84

Chapter 6 Fault Shutdown and Troubleshooting ................................. 86

6.1 LED Fault and Troubleshooting ..................................................... 86

6.2 Fault and Troubleshooting .............................................................. 88

Chapter 7 Product Maintenance ............................................................ 96

7.1 General Maintenance ...................................................................... 96

Chapter 8 Technical Data ....................................................................... 102

Chapter 9 Limited Warranty ................................................................... 107

Summary of Contents for CPS SCH Series
















































































































Search results

Summary of Contents for CPS SCH Series

Reviews:

Related manuals for CPS SCH Series

Brands by name

Popular brands

Chint Power CPS SCH Series, Installation And Operation Manual

Search results

Summary of Contents for CPS SCH Series

Reviews:

Related manuals for CPS SCH Series

Brands by name

Popular brands