Chevrolet Silverado 2013 Owner'S Manual Download Page 428 | Manualshive

Page: 428 / 544

background image

Black plate (52,1)

Chevrolet Silverado Owner Manual - 2013 - crc 1st edition - 4/5/12

10-52

Vehicle Care

(G) Single Tire Maximum
Load

:

Maximum load that can

be carried and the maximum
pressure needed to support that
load when used as a single. For
information on recommended
tire pressure see

Tire Pressure

on page 10

‑

56

and

Vehicle Load

Limits on page 9

‑

15

.

Tire Designations

Tire Size

The examples show a typical
passenger vehicle and light
truck tire size.

Passenger (P

‐

Metric) Tire

(A) Passenger (P

‐

Metric) Tire

:

The United States version of a
metric tire sizing system. The

letter P as the first character in
the tire size means a passenger
vehicle tire engineered to
standards set by the U.S. Tire
and Rim Association.

(B) Tire Width

:

The three

‐

digit

number indicates the tire section
width in millimeters from
sidewall to sidewall.

(C) Aspect Ratio

:

A two

‐

digit

number that indicates the tire
height

‐

to

‐

width measurements.

For example, if the tire size
aspect ratio is 75, as shown in
item C of the tire illustration, it
would mean that the tire's
sidewall is 75 percent as high as
it is wide.

(D) Construction Code

:

A

letter code is used to indicate
the type of ply construction in
the tire. The letter R means
radial ply construction; the
letter D means diagonal or bias

ply construction; and the letter B
means belted

‐

bias ply

construction.

(E) Rim Diameter

:

Diameter of

the wheel in inches.

(F) Service Description

:

These

characters represent the load
index and speed rating of the
tire. The load index represents
the load carrying capacity a tire
is certified to carry. The speed
rating is the maximum speed a
tire is certified to carry a load.

Light Truck (LT

‐

Metric) Tire

(A) Light Truck (LT

‐

Metric)

Tire

:

The United States version

of a metric tire sizing system.
The letters LT as the first two
characters in the tire size mean

«
...
426
427
428
429
430
...
»

Summary of Contents for Silverado 2013

































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Silverado 2013

Green Motion Building

Brand: Eaton Pages: 12

Brand: Volvo Pages: 188

Quattroporte Automatic

Brand: Maserati Pages: 272

DELTA DL FIX 209FP

Brand: Menabo Pages: 8

Brand: Porsche Pages: 313

Brand: Fab Fours Pages: 19

Brand: ACV Pages: 2

Brand: Paser Pages: 2

Brand: Xblitz Pages: 56

Brand: PUTCO Pages: 2

Brand: FORM FIT Pages: 2

Brand: Magneti Marelli Pages: 3

2013 Zafira Tourer

Brand: Vauxhall Pages: 289

Brand: Istar Pages: 6

Brand: PEUGEOT Pages: 404

Brand: Alfa Romeo Pages: 268

Brand: Safe Fleet Pages: 2

Brand: Jackson Racing Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands