Chevrolet Silverado 2013 Owner'S Manual Download Page 16

Page: 16 / 544

Black plate (10,1)

Chevrolet Silverado Owner Manual - 2013 - crc 1st edition - 4/5/12

1-10

In Brief

Pull the switch to close the
window.

The power sliding rear window
cannot be operated manually.

Seat Adjustment

Manual Seats

To adjust the seat:

1. Lift the bar to unlock the seat.

2. Slide the seat to the desired

position and release the bar.

3. Try to move the seat back and

forth to be sure the seat is
locked in place.

See

Seat Adjustment on page 3

‑

Power Seats

To adjust a power seat, if equipped:

Move the seat forward or
rearward by sliding the control
forward or rearward.

If available, raise or lower the
front or rear part of the seat
cushion by moving the front or
rear of the control up or down.

If available, raise or lower the
entire seat by moving the entire
control up or down.

See

Power Seat Adjustment on

page 3

‑

Lumbar Adjustment

Manual Lumbar

If equipped, increase or decrease
manual lumbar support by turning
the knob forward or rearward.

See

Lumbar Adjustment on

page 3

‑

Summary of Contents for Silverado 2013

































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Silverado 2013

Reviews:

Related manuals for Silverado 2013

Brands by name

Popular brands

Chevrolet Silverado 2013, Owner'S Manual

Search results

Summary of Contents for Silverado 2013

Reviews:

Related manuals for Silverado 2013

Brands by name

Popular brands