Chevrolet Silverado 2013 Owner'S Manual Download Page 382

Page: 382 / 544

Black plate (6,1)

Chevrolet Silverado Owner Manual - 2013 - crc 1st edition - 4/5/12

10-6

Vehicle Care

Engine Air Cleaner/Filter on
page 10

‑

B. Coolant Surge Tank and

Pressure Cap. See

Cooling

System on page 10

‑

C. Positive (+) Terminal. See

Jump

Starting on page 10

‑

Battery on page 10

‑

E. Remote Negative (

−

) Terminal

(Out of View). See

Jump

Starting on page 10

‑

Automatic Transmission
Dipstick (Out of View). See

“

Checking the Fluid Level

”

under

Automatic Transmission

Fluid (4-Speed Transmission)
on page 10

‑

Automatic

Transmission Fluid (6-Speed
Transmission) on page 10

‑

G. Engine Oil Fill Cap. See

“

When

to Add Engine Oil

”

under

Engine Oil on page 10

‑

H. Engine Oil Dipstick (Out of

View). See

“

Checking Engine

Oil

”

under

Engine Oil on

page 10

‑

Engine Cooling Fan (Out of
View). See

Cooling System on

page 10

‑

Power Steering Fluid Reservoir.
See

Power Steering Fluid on

page 10

‑

K. Brake Master Cylinder

Reservoir. See

Brake Fluid on

page 10

‑

Engine Compartment Fuse
Block on page 10

‑

M. Windshield Washer Fluid

Reservoir. See

“

Adding Washer

Fluid

”

under

Washer Fluid on

page 10

‑

If the vehicle has a diesel engine
and/or an Allison Transmission, see
the Duramax Diesel Supplement.

Engine Oil

For diesel engine vehicles, see

“

Engine Oil

”

in the Duramax Diesel

Supplement.

To ensure proper engine
performance and long life, careful
attention must be paid to engine oil.
Following these simple, but
important steps will help protect
your investment:

Always use engine oil approved
to the proper specification and of
the proper viscosity grade. See

“

Selecting the Right Engine Oil

”

in this section.

Check the engine oil level
regularly and maintain the
proper oil level. See

“

Checking

Engine Oil

”

and

“

When to Add

Engine Oil

”

in this section.

Change the engine oil at the
appropriate time. See

Engine Oil

Life System on page 10

‑

Always dispose of engine oil
properly. See

“

What to Do with

Used Oil

”

in this section.

Summary of Contents for Silverado 2013

































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Silverado 2013

Reviews:

Related manuals for Silverado 2013

Brands by name

Popular brands

Chevrolet Silverado 2013, Owner'S Manual

Search results

Summary of Contents for Silverado 2013

Reviews:

Related manuals for Silverado 2013

Brands by name

Popular brands