Chevrolet Silverado 2013 Owner'S Manual Download Page 488 | Manualshive

Page: 488 / 544

background image

Black plate (12,1)

Chevrolet Silverado Owner Manual - 2013 - crc 1st edition - 4/5/12

11-12

Service and Maintenance

Recommended Fluids, Lubricants, and Parts

Recommended Fluids and Lubricants

This maintenance section applies to vehicles with a gasoline engine. If the vehicle has a diesel engine and/or an
Allison Transmission, see the maintenance schedule section in the Duramax Diesel Supplement.

Fluids and lubricants identified below by name, part number, or specification can be obtained from your dealer.

Usage

Fluid/Lubricant

Engine Oil

Use only engine oil licensed to the dexos1 specfication, or equivalent, of
the proper SAE viscosity grade. ACDelco dexos1 Synthetic Blend is
recommended. See

Engine Oil on page 10

‑

6

.

Engine Coolant

50/50 mixture of clean, drinkable water and use only DEX-COOL coolant.
See

Engine Coolant on page 10

‑

18

.

Hydraulic Brake System

DOT 3 Hydraulic Brake Fluid (GM Part No. 12377967, in
Canada 89021320).

Hydraulic Clutch System

DOT 3 Hydraulic Brake Fluid (GM Part No. 12377967, in
Canada 89021320).

Windshield Washer

Automotive windshield washer fluid that meets regional freeze protection
requirements.

Power Steering System

GM Power Steering Fluid (GM Part No. 89021184, in Canada 89021186).

Automatic Transmission

DEXRON®-VI Automatic Transmission Fluid.

«
...
486
487
488
489
490
...
»

Summary of Contents for Silverado 2013

































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Silverado 2013

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 2

Brand: Cadillac Pages: 494

Brand: Cadillac Pages: 500

Brand: Cadillac Pages: 40

Brand: Cadillac Pages: 432

Brand: Cadillac Pages: 338

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 438

Brand: Dakota Digital Pages: 2

Brand: Dakota Digital Pages: 7

Brand: RaceChip Pages: 20

Brand: Yakima Pages: 7

Brand: Yakima Pages: 6

Brand: Yakima Pages: 10

Brand: Yakima Pages: 12

PACCAR PACMOBILE 20

Brand: DAF Pages: 18

Brand: Yakima Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands