Chevrolet Silverado 2013 Owner'S Manual Download Page 134

Page: 134 / 544

Black plate (2,1)

Chevrolet Silverado Owner Manual - 2013 - crc 1st edition - 4/5/12

5-2

Instruments and Controls

Transmission Messages . . . . . 5-44
Vehicle Reminder

Messages . . . . . . . . . . . . . . . . . . 5-45

Washer Fluid Messages . . . . . 5-46

Vehicle Personalization

Vehicle Personalization (With

DIC Buttons) . . . . . . . . . . . . . . . 5-46

Universal Remote System

Universal Remote System . . . 5-54
Universal Remote System

Programming . . . . . . . . . . . . . . . 5-54

Universal Remote System

Operation . . . . . . . . . . . . . . . . . . 5-59

Controls

Steering Wheel
Adjustment

To adjust the steering wheel:

1. Hold the steering wheel and pull

the lever.

2. Move the steering wheel up

or down.

3. Release the lever to lock the

wheel in place.

Do not adjust the steering wheel
while driving.

Steering Wheel Controls

If equipped, some audio controls
can be adjusted at the steering
wheel.

(Next):

Press to go to the next

favorite radio station, track on a CD,
or folder on an iPod® or USB
device.

(Previous/End):

Press to

go to the previous favorite radio
station, track on a CD, or folder on

Summary of Contents for Silverado 2013

































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Silverado 2013

Reviews:

Related manuals for Silverado 2013

Brands by name

Popular brands

Chevrolet Silverado 2013, Owner'S Manual

Search results

Summary of Contents for Silverado 2013

Reviews:

Related manuals for Silverado 2013

Brands by name

Popular brands