manualshive.com logo in svg

Chevrolet Silverado 2013, Owner'S Manual

The Chevrolet Silverado 2013 Owner's Manual is your go-to guide for understanding and operating this powerful and reliable truck. Available for free download, this comprehensive manual provides detailed instructions and helpful tips to enhance your Silverado experience. Visit manualshive.com now to access your digital copy and unleash the full potential of your vehicle.

Share
Download
background image

Black plate (96,1)

Chevrolet Silverado Owner Manual - 2013 - crc 1st edition - 4/5/12

9-96

Driving and Operating

headlamps as a second way to
boost the vehicle system and
charge the battery.

Camper/Fifth-Wheel Trailer Wiring
Package

The seven-wire camper harness is
located under the front edge of the
pickup box on the driver side of the
vehicle, attached to the frame
bracket. A connector must be added
to the wiring harness which
connects to the camper.

The harness contains the following
camper/trailer circuits:

.

Yellow: Left Stop/Turn Signal

.

Dark Green: Right Stop/Turn
Signal

.

Brown: Taillamps

.

White: Ground

.

Light Green: Back-up Lamps

.

Red: Battery Feed

.

Dark Blue: Trailer Brake

If the vehicle is equipped with the

“

Heavy-Duty Trailering

”

option,

please refer to

“

Heavy-Duty Trailer

Wiring Package

”

earlier in this

section.

When the camper-wiring harness is
ordered without the heavy-duty
trailering package, a seven-wire
harness with a seven-pin connector
is located at the rear of the vehicle
and is tied to the vehicle's frame.

Electric Brake Control Wiring
Provisions

These wiring provisions are
included with the vehicle as part of
the trailer wiring package. These
provisions are for an electric brake
controller. The instrument panel
contains blunt cut wires behind the
steering column for the trailer brake
controller. The harness contains the
following wires:

.

Dark Blue: Brake Signal to
Trailer Connector

.

Red/Black: Battery

.

Light Blue/White: Brake Switch

.

White: Ground

The harness should be installed by
your dealer or a qualified service
center.

If the vehicle is equipped with an
Integrated Trailer Brake Control
(ITBC) System, the blunt cuts exist,
but are not connected further in the
harness. If an aftermarket trailer
brake controller is installed, the

Summary of Contents for Silverado 2013

































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Silverado 2013

GMC HUMMER EV 2022 Manual preview
HUMMER EV 2022
Brand: GMC Pages: 140
Cadillac ESCALADE - BROCHURE 2009 Personalization Manual preview
ESCALADE - BROCHURE 2009
Brand: Cadillac Pages: 24
Cadillac Escalade Personalization Manual preview
Escalade
Brand: Cadillac Pages: 20
Cadillac Escalade 2016 Convenience/Personalization Manual preview
Escalade 2016
Brand: Cadillac Pages: 20
Jeep UNIVERSAL CJ-2A Operation Data preview
UNIVERSAL CJ-2A
Brand: Jeep Pages: 27
Jeep RENEGADE 2016 User Manual preview
RENEGADE 2016
Brand: Jeep Pages: 228
Jeep PATRIOT 2013 User Manual preview
PATRIOT 2013
Brand: Jeep Pages: 108
Jeep PATRIOT 2013 Owner'S Manual preview
PATRIOT 2013
Brand: Jeep Pages: 525
Vauxhall 2009 Tigra Quick Reference Manual preview
2009 Tigra
Brand: Vauxhall Pages: 2
Yakima K800 Instructions Manual preview
K800
Brand: Yakima Pages: 8
Actia SmarTach Manual preview
SmarTach
Brand: Actia Pages: 102
P-Invent Troller User Manual preview
Troller
Brand: P-Invent Pages: 4
Lit Lightz RGBW Rock Lights Setup Manual preview
RGBW Rock Lights
Brand: Lit Lightz Pages: 3
Park-Daddy PD50AA Installation Manual preview
PD50AA
Brand: Park-Daddy Pages: 22
U.S. General 96524 Set Up And Operating Instructions Manual preview
96524
Brand: U.S. General Pages: 8
Fab Fours H4550 Installation Instructions Manual preview
H4550
Brand: Fab Fours Pages: 13
WATT CARWATT CV12-220C150 User Manual preview
CARWATT CV12-220C150
Brand: WATT Pages: 26
TATA Motors Harrier 2021 Owner'S Manual preview
Harrier 2021
Brand: TATA Motors Pages: 308

Brands by name

Popular brands

Load more brands