Chevrolet Silverado 2013 Owner'S Manual Download Page 42 | Manualshive

Page: 42 / 544

background image

Black plate (2,1)

Chevrolet Silverado Owner Manual - 2013 - crc 1st edition - 4/5/12

2-2

Keys, Doors, and Windows

The key is used for the ignition and
all door locks.

The key has a bar-coded key tag
that the dealer or qualified locksmith
can use to make new keys. Store
this information in a safe place, not
in the vehicle.

See your dealer if a replacement
key or additional key is needed.

If the vehicle has an ignition and it
becomes difficult to turn the key,
inspect the key blade for debris.
Periodically clean with a brush
or pick.

With an active OnStar subscription,
an OnStar Advisor may remotely
unlock the vehicle. See

OnStar

Overview on page 14

‑

1

.

Remote Keyless Entry
(RKE) System

See

Radio Frequency Statement on

page 13

‑

21

for information

regarding Part 15 of the Federal
Communications Commission (FCC)
rules and Industry Canada
Standards RSS-GEN/210/220/310.

If there is a decrease in the RKE
operating range:

.

Check the distance. The
transmitter may be too far from
the vehicle.

.

Check the location. Other
vehicles or objects may be
blocking the signal.

.

Check the transmitter's battery.
See

“

Battery Replacement

”

later

in this section.

.

If the transmitter is still not
working correctly, see your
dealer or a qualified technician
for service.

Remote Keyless Entry
(RKE) System Operation

The Remote Keyless Entry (RKE)
transmitter functions work up to
60 m (195 ft) away from the vehicle.

There are other conditions which
can affect the performance of the
transmitter. See

Remote Keyless

Entry (RKE) System on page 2

‑

2

.

«
...
40
41
42
43
44
...
»

Summary of Contents for Silverado 2013

































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Silverado 2013

Brand: Saab Pages: 75

Brand: Harbor Freight Tools Pages: 4

Brand: Pacbrake Pages: 14

Brand: Edelbrock Pages: 1

Brand: FORM FIT Pages: 2

Ferrari 360 Map Carbon Light

Brand: MAcarbon Pages: 4

Brand: Hyundai Pages: 19

Brand: RBO Pages: 15

Brand: cam Pages: 6

Brand: Seat Pages: 300

2008 Savana Van

Brand: GMC Pages: 402

Brand: Brodit Pages: 2

Brand: Saturn Pages: 432

Brand: Acura Pages: 347

Turnoverball 1020

Brand: Bowers & Wilkins Pages: 6

Brand: Blue Bird Pages: 111

Brand: Brodit Pages: 2

Brand: ULTIMATE SPEED Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands