Chevrolet Silverado 2013 Owner'S Manual Download Page 358 | Manualshive

Page: 358 / 544

background image

Black plate (90,1)

Chevrolet Silverado Owner Manual - 2013 - crc 1st edition - 4/5/12

9-90

Driving and Operating

Vehicle

Axle Ratio

Maximum Trailer Weight

GCWR (a)

6.0L V8 Single Rear Wheels

—

Fifth-Wheel Trailer

4.10

5 987 kg (13,200 lb)

9 299 kg (20,500 lb)

6.0L V8 Dual Rear Wheels

3.73

3 946 kg (8,700 lb)

7 258 kg (16,000 lb)

6.0L V8 Dual Rear Wheels

4.10

5 987 kg (13,200 lb)

9 299 kg (20,500 lb)

(a) The Gross Combination Weight Rating (GCWR) is the total allowable weight of the completely loaded vehicle
and trailer including any passengers, cargo, equipment, and conversions. The GCWR for the vehicle should not be
exceeded.
(b) This model is neither designed nor intended to tow fifth-wheel or gooseneck trailers.
(c) Vehicles equipped with QXR LT245/70R17 AT C load tires should restrict GCWR to no more than 12,200 lbs.

Ask your dealer for trailering
information or advice.

Weight of the Trailer Tongue

The tongue load (A) of any trailer is
very important because it is also
part of the vehicle weight. The
Gross Vehicle Weight (GVW)
includes the curb weight of the

vehicle, any cargo carried in it, and
the people who will be riding in the
vehicle as well as trailer tongue
weight. Vehicle options, equipment,
passengers and cargo in the vehicle
reduce the amount of tongue weight
the vehicle can carry, which will also
reduce the trailer weight the vehicle
can tow. See

“

Vehicle Load Limits

”

for more information about the
vehicle's maximum load capacity.

«
...
356
357
358
359
360
...
»

Summary of Contents for Silverado 2013

































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Silverado 2013

Brand: AA Products Pages: 8

Brand: Yakima Pages: 11

Brand: Jeep Pages: 12

Brand: Jeep Pages: 6

Brand: Farad Pages: 8

Brand: Yakima Pages: 8

Brand: SnapPad Pages: 5

Brand: Chariot Carriers Pages: 3

FIX&GO automatic

Brand: Alfa Romeo Pages: 40

Brand: PAC Pages: 4

Brand: HAUL MASTER Pages: 8

Brand: M7 SPEED Pages: 6

Brand: Skoda Pages: 324

Brand: NavInc Pages: 6

Denali 1094-0185-15

Brand: E&G Classics Pages: 3

Brand: Metra Electronics Pages: 2

Brand: Hama Pages: 13

Brand: Magneti Marelli Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands