manualshive.com logo in svg

Chevrolet Silverado 2013, Owner'S Manual

The Chevrolet Silverado 2013 Owner's Manual is your go-to guide for understanding and operating this powerful and reliable truck. Available for free download, this comprehensive manual provides detailed instructions and helpful tips to enhance your Silverado experience. Visit manualshive.com now to access your digital copy and unleash the full potential of your vehicle.

Share
Download
background image

Black plate (97,1)

Chevrolet Silverado Owner Manual - 2013 - crc 1st edition - 4/5/12

Driving and Operating

9-97

ITBC must be disconnected. Do not
power both ITBC and aftermarket
controllers to control the trailer
brakes at the same time.

Tow/Haul Mode

Pressing this button at the end of
the shift lever turns on and off the
Tow/Haul Mode.

This indicator light on the instrument
panel cluster comes on when the
Tow/Haul Mode is on.

Tow/Haul is a feature that assists
when pulling a heavy trailer or a
large or heavy load. See

Tow/Haul

Mode on page 9

‑

38

for more

information.

Tow/Haul is designed to be most
effective when the vehicle and
trailer combined weight is at least
75 percent of the vehicle's Gross
Combined Weight Rating (GCWR).
See

“

Weight of the Trailer

”

under

Trailer Towing on page 9

‑

77

. Tow/

Haul is most useful under the
following driving conditions:

.

When pulling a heavy trailer or a
large or heavy load through
rolling terrain.

.

When pulling a heavy trailer or a
large or heavy load in
stop-and-go traffic.

.

When pulling a heavy trailer or a
large or heavy load in busy
parking lots where improved low
speed control of the vehicle is
desired.

Operating the vehicle in Tow/Haul
when lightly loaded or with no trailer
at all will not cause damage.
However, there is no benefit to the
selection of Tow/Haul when the
vehicle is unloaded. Such a
selection when unloaded may result
in unpleasant engine and
transmission driving characteristics
and reduced fuel economy. Tow/
Haul is recommended only when
pulling a heavy trailer or a large or
heavy load.

Summary of Contents for Silverado 2013

































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Silverado 2013

KAP AUDI 4G HIGHEND Manual preview
AUDI 4G HIGHEND
Brand: KAP Pages: 20
Kathrein DDA Series User Manual preview
DDA Series
Brand: Kathrein Pages: 7
Mercedes-Benz R-Class Owner'S Manual preview
R-Class
Brand: Mercedes-Benz Pages: 373
Honda 08A28-0J6-800 Installation Instructions Manual preview
08A28-0J6-800
Brand: Honda Pages: 32
Subaru Impreza 2.5GT Specifications preview
Impreza 2.5GT
Brand: Subaru Pages: 2
Subaru 1999 Impreza Owner'S Manual preview
1999 Impreza
Brand: Subaru Pages: 328
Mobility Networks RPH 35.13 Use And Maintenance Manual preview
RPH 35.13
Brand: Mobility Networks Pages: 52
Saab 9000 1985 Service Manual preview
9000 1985
Brand: Saab Pages: 92
A-rival PNC70 Active Hardware Manual preview
PNC70 Active
Brand: A-rival Pages: 23
v.LOGiC V5-CIC-E-PNP Manual preview
V5-CIC-E-PNP
Brand: v.LOGiC Pages: 22
Saab 32 025 907 Installation Instructions Manual preview
32 025 907
Brand: Saab Pages: 37
KLAUS Multiparking trendvario6X00 Service Manual preview
trendvario6X00
Brand: KLAUS Multiparking Pages: 72
Buick 1988 Riviera Owner'S Manual preview
1988 Riviera
Brand: Buick Pages: 161
iSimple IS7705 Installation & Operation Manual preview
IS7705
Brand: iSimple Pages: 8
Conrad TPMS-001 Operating Instructions Manual preview
TPMS-001
Brand: Conrad Pages: 8
Yakima K1095 Instructions Manual preview
K1095
Brand: Yakima Pages: 12
PAC RPK4-CH4102 Manual preview
RPK4-CH4102
Brand: PAC Pages: 18
Kuda 193400 Installation Instruction preview
193400
Brand: Kuda Pages: 2

Brands by name

Popular brands

Load more brands