Chevrolet 2003 tracker Owner'S Manual Download | Manualshive

Page: 123 / 372

background image

Reducing Speed While Using Cruise
Control

To reduce your speed, turn the switch and hold it down
in the COAST SET position until you reach the lower
speed you want, then release the switch.

Passing Another Vehicle While Using
Cruise Control

Use the accelerator pedal to increase your speed.
When you take your foot off the pedal, your vehicle will
slow down to the cruise control speed you set earlier.

Using Cruise Control on Hills

How well your cruise control will work on hills depends
upon your speed, load and the steepness of the
hills. When going up steep hills, you may have to step
on the accelerator pedal to maintain your speed.
When going downhill, you may have to brake or shift
to a lower gear to keep your speed down. Of course,
applying the brake suspends cruise control. Many
drivers find this to be too much trouble and don’t use
cruise control on steep hills.

Suspending Cruise Control

There are two ways to suspend cruise control:

•

Step lightly on the brake pedal, or push the clutch
pedal if you have a manual transmission.

•

Push in the CANCEL button on the end of the
cruise control lever.

Ending Cruise Control

To end cruise control press CRUISE ON/OFF on the
instrument panel.

Erasing Speed Memory

Cruise control set speed memory is erased when you
turn off the CRUISE ON/OFF switch or anytime you turn
the ignition off.

3-11

«
...
121
122
123
124
125
...
»

Summary of Contents for 2003 tracker





















































































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 tracker

Brand: Kargo Master Pages: 5

Brand: Qube Pages: 19

Brand: Cadillac Pages: 32

Brand: Calira Pages: 14

Brand: Vauxhall Pages: 2

Brand: JANE Pages: 21

Brand: Jackco Pages: 11

Brand: Axxess Pages: 8

Brand: Phonocar Pages: 6

Brand: Audiovox Pages: 24

Brand: Mercedes-Benz Pages: 2

Brand: Westin Pages: 2

2010 Civic Sedan

Brand: Honda Pages: 390

Brand: Kargo Master Pages: 19

PRIME DESIGN VBR3-FT31B

Brand: Safe Fleet Pages: 12

Brand: Gator Pages: 6

Brand: Mercedes-Benz Pages: 296

Brand: Ford Pages: 458

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands