Chevrolet 2003 tracker Owner'S Manual Download | Manualshive

Page: 318 / 372

background image

Every 45,000 Miles (75 000 km): Automatic
Transmission Fluid Hose Inspection (or every
45 months, whichever occurs first).

Every 60,000 Miles (100 000 km): Fuel Tank Cap
Gasket Replacement. Emission System Hoses
Inspection. Brake Fluid Service. Spark Plug
Replacement.

Every 100,000 Miles (166 000 km): Automatic
Transmission Service (normal conditions).

Every 120 000 Miles (200 000 km): Evaporative
Emissions Canister and Air Suction Filter Replacement
(or every 120 months, whichever occurs first). Engine
Accessory Drive Belt Replacement (or every
120 months, whichever occurs first).

These intervals only summarize maintenance services.
Be sure to follow the complete scheduled maintenance
on the following pages.

Long Trip/Highway Definition

Follow this scheduled maintenance

only if none of

the conditions from the Short Trip/City Scheduled
Maintenance are true. Do not use this schedule if the
vehicle is used for trailer towing, driven in a dusty area
or used off paved roads. Use the Short Trip/City
schedule for these conditions.

Driving a vehicle with a fully warmed engine under
highway conditions will cause engine oil to break down
slower.

Long Trip/Highway Intervals

Every 7,500 Miles (12 500 km): Engine Oil and Filter
Change (or every 7.5 months, whichever occurs first).
Tire Rotation.

Every 15,000 Miles (25 000 km): Engine Air Cleaner
Filter Inspection. Automatic Transmission Service
(severe conditions only). Passenger Compartment
Air Filter Inspection (If Equipped). Propeller Shafts and
U-Joints Inspection (or every 15 months, whichever
occurs first).

6-6

«
...
316
317
318
319
320
...
»

Summary of Contents for 2003 tracker





















































































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 tracker

Brand: Cequent Pages: 9

Brand: Camcar Pages: 6

Brand: ABL Pages: 4

Brand: Honda Pages: 208

Brand: Hama Pages: 75

Brand: Acura Pages: 2

Brand: Whispbar Pages: 15

Brand: Ecco Pages: 12

OCTAVIA - TECHNICAL CHANGES 11-2009

Brand: Skoda Pages: 16

Brand: Pacbrake Pages: 6

Brand: KEKO Pages: 13

Stealth 4191F Series

Brand: Road Armor Pages: 5

Brand: Honda Pages: 569

Brand: Thule Pages: 8

ESCALADE ESV 2005

Brand: Cadillac Pages: 482

Brand: curt Pages: 4

Brand: Prime Design Pages: 8

Brand: Westin Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands