Chevrolet 2003 tracker Owner'S Manual Download | Manualshive

Page: 150 / 372

background image

Radio with CD

Playing the Radio

PWR (Power): Press this knob to turn the system
on and off.

VOL (Volume): Turn the knob to increase or to
decrease volume.

RCL (Recall): Press this knob to switch the display
between time and radio station frequency. Time display
is available with the ignition turned off.

Finding a Station

AM FM: Press this button to switch between AM, FM1
and FM2. The display will show your selection.

TUNE: Turn this knob to choose radio stations.

o

SEEK

p

: Press the right or the left arrow to seek

to the next or to the previous station and stay there.

To scan stations, press and hold one of the SEEK
arrows for two seconds until you hear a beep. The radio
will go to a station, play for a few seconds and flash
the station frequency, then go on to the next station.
Press one of the SEEK arrows again to stop scanning.

To scan preset stations, press and hold one of the
SEEK arrows for more than four seconds until you hear
two beeps. The radio will go to the first preset station
stored on your pushbuttons, play for a few seconds and
flash the station frequency, then go on to the next
preset station. Press one of the SEEK arrows again to
stop scanning presets.

The radio will seek and scan only to stations that are in
the selected band and only to those with a strong signal.

3-38

«
...
148
149
150
151
152
...
»

Summary of Contents for 2003 tracker





















































































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 tracker

Brand: Cequent Pages: 9

Brand: Axxess Pages: 8

Brand: SeaSucker Pages: 9

Brand: WABCO Pages: 32

Brand: femkes Pages: 7

Brand: Menabo Pages: 12

Brand: TAUBENREUTHER Pages: 8

Brand: Mini Pages: 20

Brand: Right Weigh Pages: 16

Brand: Icom Pages: 20

Electra 225 1965

Brand: Buick Pages: 914

Brand: Cadillac Pages: 409

Brand: Fortin Pages: 9

Brand: Ecco Pages: 24

Brand: Thule Pages: 4

Brand: Rigid Hitch Pages: 2

Brand: Federal Signal Corporation Pages: 20

Brand: AD Boivin Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands