manualshive.com logo in svg

Chevrolet 2003 tracker, Owner'S Manual

The Chevrolet 2003 Tracker manual is available for free download on our website. This comprehensive user manual offers detailed instructions and valuable information on operating and maintaining your Chevrolet Tracker. Download it today from manualshive.com to enhance your driving experience and ensure optimal vehicle performance.

Share
Download
background image

Front Axle

When to Check and Change Lubricant

Refer to the Maintenance Schedule to determine how
often to check the lubricant and when to change it.
See

Part C: Periodic Maintenance

I

nspections on

page 6-28 and Part A: Scheduled Maintenance Services
on page 6-4.

How to Check Lubricant

To get an accurate reading, the vehicle should be on a
level surface.

If the level is below the bottom of the filler plug hole,
you may need to add some lubricant.

1. Remove the filler plug.

2. Remove the drain plug, drain the lubricant and

reinstall the drain plug.

3. When the differential is cold, add enough lubricant

to raise the level to 1/2 inch (12 mm) below the filler
plug hole.

When the differential is at operating temperature
(warm), add enough lubricant to raise the level
to the bottom of the filler plug hole.

4. Reinstall the filler plug.

What to Use

Refer to the Maintenance Schedule to determine what
kind of lubricant to use. See

Part D: Recommended

Fluids and Lubricants on page 6-30.

5-54

Summary of Contents for 2003 tracker





















































































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 tracker

EUFAB 12015 Manual preview
12015
Brand: EUFAB Pages: 12
Wilco Offroad UHG2060/AU Installation Manual preview
UHG2060/AU
Brand: Wilco Offroad Pages: 4
Ford 2004 Navigator Owner'S Manual preview
2004 Navigator
Brand: Ford Pages: 368
Würth 071554055 User Instructions preview
071554055
Brand: Würth Pages: 36
Weltmann KFZ-Teile 9B500016 Fitting Instructions Manual preview
9B500016
Brand: Weltmann KFZ-Teile Pages: 12
Federal Signal Corporation Cuda TriOptic 351014F Series Instruction Sheet preview
Cuda TriOptic 351014F Series
Brand: Federal Signal Corporation Pages: 4
Kia Magentis 2002 Owner'S Manual preview
Magentis 2002
Brand: Kia Pages: 216
Ford FLEX 2019 Quick Reference Manual preview
FLEX 2019
Brand: Ford Pages: 10
Fiat Panda 2015 Owner'S Handbook Manual preview
Panda 2015
Brand: Fiat Pages: 204
Paser SKT 170 HYUNDAI Installation Manual preview
SKT 170 HYUNDAI
Brand: Paser Pages: 4
Yakima PR3041 Fitting Instructions Manual preview
PR3041
Brand: Yakima Pages: 13
Dakota Digital VFD3-52F Installation preview
VFD3-52F
Brand: Dakota Digital Pages: 2
Toyota Prius Plug-inHybrid Quick Reference Manual preview
Prius Plug-inHybrid
Brand: Toyota Pages: 40
Edscha Trailer Systems CS-LitePlus Quick Manual preview
CS-LitePlus
Brand: Edscha Trailer Systems Pages: 120
Blueant BLUEANT Z9 User Manual preview
BLUEANT Z9
Brand: Blueant Pages: 137
Stoneridge SE5000 Control Manual preview
SE5000
Brand: Stoneridge Pages: 34
Ultraflex ND1-MM Installation Manual preview
ND1-MM
Brand: Ultraflex Pages: 40
Silvercrest SLM 11 B2 Operating Instructions preview
SLM 11 B2
Brand: Silvercrest Pages: 2

Brands by name

Popular brands

Load more brands