Chevrolet 2003 tracker Owner'S Manual Download | Manualshive

Page: 206 / 372

background image

Dolly Towing

To tow your vehicle from the rear, do the following:

The best way to tow your vehicle is from the rear.
Follow these steps:

1. Put the rear wheels on a dolly.

Notice: If you tow a two-wheel-drive vehicle with
the rear wheels on the ground, the transmission
could be damaged. The repairs would not be
covered by your warranty. Never tow your vehicle
with the rear wheels on the ground.

2. If your vehicle is a four-wheel-drive vehicle,

turn the ignition key to ON, move the transfer case
lever into NEUTRAL and make sure the 4WD
light on the instrument panel cluster is turned off.
See

Four-Wheel Drive on page 5-53.

3. Turn the ignition key to ACC.

4. Make sure the front wheels are facing straight

forward and secure the steering wheel with a
steering wheel clamping device designed for towing.

Notice: If you exceed 55 mph (90 km/h) while
towing your vehicle, it could be damaged. Never
exceed 55 mph (90 km/h) while towing your vehicle.

{

CAUTION:

Shifting a four-wheel-drive vehicle’s transfer
case into NEUTRAL can cause your vehicle to
roll even if the transmission is in Park (P) for
an automatic transmission, or if your vehicle is
in gear, for a manual transmission. You or
others could be injured. Make sure the parking
brake is firmly set before you shift the transfer
case to NEUTRAL.

4-50

«
...
204
205
206
207
208
...
»

Summary of Contents for 2003 tracker





















































































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 tracker

Brand: Valeo Pages: 17

Brand: Camoplast Pages: 60

Green Motion Building

Brand: Eaton Pages: 12

Brand: kincrome Pages: 6

Chevrolet Silverado 2500HD 2021

Brand: GMC Pages: 433

Brand: Fab Fours Pages: 19

PRIME DESIGN VBI-FT21B

Brand: Safe Fleet Pages: 12

Plusone Console 4521011B

Brand: Honda Pages: 4

STO N SHO SNS 144

Brand: Big Mikes Performance Parts Pages: 7

Brand: Lincoln Pages: 10

Brand: Volvo Pages: 266

Brand: Cadillac Pages: 2

Brand: Buick Pages: 20

FlashLogic FLC-FORS-FO1B-FLRSFO1-EN

Brand: ADS Pages: 25

Brand: Acura Pages: 7

Brand: Jaeger Pages: 14

Brand: CSL Pages: 8

Brand: Kuda Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands