Chevrolet 2003 tracker Owner'S Manual Download | Manualshive

Page: 201 / 372

background image

Rocking Your Vehicle To Get It Out

First, turn your steering wheel left and right. That will
clear the area around your front wheels. If you have the
four-speed automatic, see “Power Mode Selector
Switch” under

Automatic Transmission Operation on

page 2-19 for information on traction. If you have
a four-wheel-drive vehicle, shift into 4HI. Then shift back
and forth between REVERSE (R) and a forward gear
(or with a manual transmission, between FIRST (1)
or SECOND (2) and REVERSE (R)), spinning the
wheels as little as possible. Release the accelerator
pedal while you shift, and press lightly on the accelerator
pedal when the transmission is in gear. By slowly
spinning your wheels in the forward and reverse
directions, you will cause a rocking motion that may free
your vehicle. If that doesn’t get you out after a few
tries, you may need to be towed out. Or, you can use
your recovery hooks. If you do need to be towed
out, see

Towing Your Vehicle on page 4-47.

Using the Recovery Hooks

Your vehicle is equipped with recovery hooks.
The hooks are provided at the front and rear of your
vehicle. You may need to use them if you’re stuck
off-road and need to be pulled to some place where
you can continue driving.

4-45

«
...
199
200
201
202
203
...
»

Summary of Contents for 2003 tracker





















































































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 tracker

Brand: GARO Pages: 23

LS4 Wallmounted

Brand: GARO Pages: 15

Brand: LAS Pages: 44

Brand: LAS Pages: 24

Brand: Vauxhall Pages: 199

Brand: Fabbri Pages: 4

Brand: Romik Pages: 6

Brand: EUFAB Pages: 12

Brand: Würth Pages: 36

Brand: NavLinkz Pages: 21

Brand: BMW Pages: 55

Brand: Whispbar Pages: 15

Brand: Subaru Pages: 2

Brand: Subaru Pages: 328

Brand: Daesung Pages: 9

Brand: Pontiac Pages: 318

Brand: KEKO Pages: 13

Stealth 4191F Series

Brand: Road Armor Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands