Chevrolet 2003 tracker Owner'S Manual Download | Manualshive

Page: 250 / 372

background image

The coolant level should be at or above FULL. If it isn’t,
you may have a leak at the pressure cap or in the
radiator hoses, heater hoses, radiator, water pump or
somewhere else in the cooling system.

{

CAUTION:

Heater and radiator hoses, and other engine
parts, can be very hot. Do not touch them.
If you do, you can be burned.

Do not run the engine if there is a leak. If you
run the engine, it could lose all coolant. That
could cause an engine fire, and you could be
burned. Get any leak fixed before you drive the
vehicle.

If there seems to be no leak, start the engine again.
The engine cooling fan speed should increase when idle
speed is doubled by pushing the accelerator pedal
down. If it doesn’t, your vehicle needs service. Turn off
the engine.

Notice: Engine damage from running your engine
without coolant isn’t covered by your warranty.

5-34

«
...
248
249
250
251
252
...
»

Summary of Contents for 2003 tracker





















































































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 tracker

Brand: Daihatsu Pages: 485

Brand: JANE Pages: 21

LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...

Brand: Dakota Digital Pages: 3

Brand: ideus Pages: 159

Brand: Prorack Pages: 10

TX-STAMP-4-FC04

Brand: Over Armour Offroad Pages: 9

Brand: Subaru Pages: 540

Brand: Skoda Pages: 324

Brand: NavInc Pages: 6

Denali 1094-0185-15

Brand: E&G Classics Pages: 3

Brand: Metra Electronics Pages: 2

Brand: Metra Electronics Pages: 8

Brand: Pogo Pages: 40

Brand: Uniden Pages: 16

Brand: Buick Pages: 112

Brand: Kargo Master Pages: 17

Brand: Bazooka Pages: 2

10-8002-C12167A

Brand: Saleen Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands