Chevrolet 2003 tracker Owner'S Manual Download | Manualshive

Page: 140 / 372

background image

Charging System Light

This light will come on
briefly when you turn on the
ignition, but the engine is
not running, as a check to
show you it is working.
Then it should go out when
the engine starts.

If the light stays on or comes on while you are driving,
you may have a problem with the electrical charging
system. It could indicate that you have an electrical
problem. Have it checked right away. Driving while this
light is on could drain your battery.

If you must drive a short distance with this light on, be
certain to turn off all your accessories, such as the radio
and air conditioner.

Brake System Warning Light

When the ignition is on, the brake system warning light
will come on when you set your parking brake. The
light will stay on if your parking brake doesn’t release
fully. If it stays on after your parking brake is fully
released, it means you have a brake problem.

Your vehicle’s hydraulic brake system is divided into two
parts. If one part isn’t working, the other part can still
work and stop you. For good braking, though, you need
both parts working well.

If the warning light comes on, there could be a brake
problem. Have your brake system inspected right away.

3-28

«
...
138
139
140
141
142
...
»

Summary of Contents for 2003 tracker





















































































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 tracker

Brand: FORM FIT Pages: 2

Brand: Ironton Pages: 7

LeisureWize EMOVE EM303A

Brand: Streetwize Pages: 20

PRIME DESIGN VRR-E-PM21

Brand: Safe Fleet Pages: 12

Brand: FALCON RIDGE Pages: 7

Brand: Volvo Pages: 30

Brand: Ecco Pages: 9

Brand: FALCON RIDGE Pages: 4

Brand: Enduro Pages: 52

Brand: Conrad Pages: 50

Brand: Sintrones Pages: 55

Brand: Gator Pages: 5

Pro Competition

Brand: G-Tech Pages: 180

Brand: Lexus Pages: 609

MULTI VEHICLE MOUNT MVM-45-05

Brand: Bracketron Pages: 4

Quad Gear 18-029-010401-00-SC

Brand: Classic Accessories Pages: 4

AC-12PROWLER-FC04

Brand: FALCON RIDGE Pages: 9

Brand: ikross Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands