Chevrolet 2003 tracker Owner'S Manual Download | Manualshive

Page: 130 / 372

background image

Climate Controls

Climate Control System

With this system you can control the heating, cooling
and ventilation for your vehicle.

Operation

9

(Fan): Move the lever away from OFF to turn the

system on. Slide the top right lever to the left or right to
increase or decrease the fan speed.

If the airflow seems low when the fan is at the
highest setting, the passenger compartment air filter,
if equipped, may need to be replaced. For more
information, see

Passenger Compartment Air Filter on

page 3-22 and Short Trip/City Scheduled Maintenance
on page 6-7.

Slide the top left lever to the left or right to direct the
airflow inside of your vehicle.

To change the current mode, select one of the following:

H

(Vent): This mode directs air to the instrument

panel outlets.

)

(Bi-Level): This mode directs most of the air to the

instrument panel outlets, and then directs the remaining
air to the floor outlets.

6

(Floor): This mode directs half of the air to the

floor outlets with some air directed to the outboard
outlets (for the side windows) and some air directed to
the windshield.

This lever can also be used to select defog or defrost
mode. Information on defogging and defrosting can
be found later in this section.

3-18

«
...
128
129
130
131
132
...
»

Summary of Contents for 2003 tracker





















































































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 tracker

Brand: Safe Fleet Pages: 11

Brand: Camec Pages: 19

Brand: Xhorse Pages: 48

Brand: Opel Pages: 32

OCTAVIA - TECHNICAL CHANGES 11-2009

Brand: Skoda Pages: 16

Brand: Improved Racing Pages: 17

Portable Car Umbrella

Brand: Mynew Pages: 5

Brand: Oldsmobile Pages: 358

Brand: Scosche Pages: 8

Brand: ZENEC Pages: 2

Brand: Hama Pages: 39

Brand: SAAS Pages: 3

Brand: Nuna Pages: 29

Brand: Kargo Master Pages: 8

Brand: Kuda-Phonebase Pages: 3

2009 ESCALADE EXT

Brand: Cadillac Pages: 1

2002 Silverado 1500 Pickup

Brand: Chevrolet Pages: 497

Brand: Chevrolet Pages: 402

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands