Chevrolet 2003 tracker Owner'S Manual Download | Manualshive

Page: 164 / 372

background image

Avoid needless heavy braking. Some people drive
in spurts — heavy acceleration followed by heavy
braking — rather than keeping pace with traffic.
This is a mistake. Your brakes may not have time to
cool between hard stops. Your brakes will wear
out much faster if you do a lot of heavy braking.
If you keep pace with the traffic and allow realistic
following distances, you will eliminate a lot of
unnecessary braking. That means better braking and
longer brake life.

If your engine ever stops while you are driving, brake
normally but do not pump your brakes. If you do,
the pedal may get harder to push down. If your engine
stops, you will still have some power brake assist.
But you will use it when you brake. Once the power
assist is used up, it may take longer to stop and
the brake pedal will be harder to push.

Anti-lock Brake System (ABS)

Your vehicle may have anti-lock brakes. ABS is an
advanced electronic braking system that will help
prevent a braking skid.

If your vehicle has anti-lock
brakes, this warning light
on the instrument panel will
come on briefly when
you start your vehicle.

When you start your engine, or when you begin to drive
away, your anti-lock brake system will check itself.
You may hear a momentary motor or clicking noise while
this test is going on, and you may even notice that
your brake pedal moves or pulses a little. This is normal.

If there is a problem with the anti-lock brake system,
the anti-lock brake system warning light will stay on.
See

Anti-Lock Brake System Warning Light on

page 3-30.

4-8

«
...
162
163
164
165
166
...
»

Summary of Contents for 2003 tracker





















































































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 tracker

Brand: Ford Pages: 12

Brand: Chevrolet Pages: 356

Brand: Ford Pages: 272

Brand: Pontiac Pages: 376

Brand: Jeep Pages: 712

Brand: Menabo Pages: 12

Brand: tams elektronik Pages: 44

Brand: Yakima Pages: 12

Brand: J. Strong Pages: 2

Brand: Mazda Pages: 1001

Brand: Westin Pages: 3

Brand: Kuda Pages: 3

Brand: Bulldog Security Pages: 7

Brand: DICE Pages: 1

Brand: Hudson Pages: 24

Brand: CITROEN Pages: 394

Brand: Mercedes-Benz Pages: 66

Brand: MBW Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands