manualshive.com logo in svg

Carrier Pro-Dialog CONTROL 4, User Manual

Share
Download
Carrier Pro-Dialog CONTROL 4 User Manual Download Page 35

This decision specifies the amount of time that will be allowed to elapse between alarm retries. Retries occur
when an alarm is not acknowledged by a network alarm acknowledger, which may be either a Building
Supervisor, an Autodial Gateway, or a Dataport 2. If the acknowledgement is not received, the alarm will be
retransmitted after the number of minutes specified in this decision.

Allowable Entries

1 to 240 minutes

Default

10 minutes

REALARM TIME

This decision specifies the amount of time that will be allowed to elapse between re-alarms. A re-alarm
occurs when the condition that caused the initial alarm continues to persist for the number of minutes
specified in this decision. Re-alarming will continue to occur at the specified interval until the condition
causing the alarm is corrected.

Allowable Entries

1 to 254 minutes

Default

30 minutes

ALARM SYSTEM NAME

This decision specifies the system element name that will appear in alarms generated by the Pro-Dialog
control.

Allowable Entries

Up to 8 alphanumeric characters

Default

PRO_30GX

© 

C

ARRIER

 

S

.

A

NOT

 

TO

 

BE

 

DISCLOSED

 

TO

 

PERSONS

 

OUTSIDE

 

CARRIER

 

ORGANIZATION

                              CARRIER SA

USER'S GUIDE FOR 

30GX&HX PRO_DIALOG 4  V.2

 

ECG - UG - 02 - 02

Rev: Original

Page: 34 /98

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for Pro-Dialog CONTROL 4





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands