![background image](http://html.mh-extra.com/html/carrier/80hma-m00/80hma-m00_installation-operation-and-maintenance-instructions_2563379032.webp)
32
80HMA
The procedures given in the coming sections help to
!
with a standardized architecture.
Refer to schematics: Scheme-01 and Schme-02
This will be helpful for system comprehension and
troubleshooting.
-
Assuming that all checks are done regarding
!! %
!
-
Two tools are offered in the unit: Automatic
Addressing Process (AAP) and Manual Addressing
Process (MAP).
-
Automatic Addressing Process (AAP) is only
+&'&$ ,!!%!&
check the label on master/slave boards.
3.3.3.1 Automatic Addressing Process, AAP
[Par.129]
Principle:
The AAP tool provides an automatic process to avoid too
!& %, $,$
MAP tool.
When Par.129 is set to 1 Auto addressing is performed
automatically at power supply on (main Circuit breaker).
J$$ ! !!&=%!
Par.129 will be set automatically to 0.
, && '&&'%
%! $
addresses is completed.
Par.129 is set to 0 by default (factory default value).The
user can set this value anytime to 0 or 1 using the user
$%";
Auto-addressing does not send the "clear the network"
command; allowing to add boards step by step.
; 'Q $ %
"clear the network" command has to be sent (Set Par.121: 7
and press ok) prior to redoing the Auto-Addressing Process
by setting Par.129 to 1.
3.3.3.2 Automatic Addressing Process, AAP
[Par.129] step by step
Principle: This process is used to assign boards address
following network architecture given in Scheme-01 and
Scheme-02.
1. ' +'%$
'%& 'YJQ !J¨
Initialization of boards to default address.
2. Go to NUI(0) – Master Board
3. +'&'&!%!
&
& &$ %|©$
more information).
4. Set the parameter Par.129: 1 AAP will be activated for
30 minutes continuous power supply.
5. Power
OFF.
6. Disconnect the bus from boards that should be
addressed at the same time and follow the process
according to your system schematic.
1. For Schematic Scheme-01
a. Connect the boards: Master Board (address 10)
+ NUI(0) (address 85) + Pool kit slave board if
existing (address 21) + 30AWH communicant HP
(address 2)
b. Power ON to run the AAP – Wait for 30 sec
c. Power OFF and connect the NUI(1) (address
}%$
d. Power ON to run the AAP – Wait for 30 sec
e. Power OFF and connect the NUI(2) (address
}%$
f. Power ON to run the AAP – Wait for 30 sec
2. For Schematic Scheme-02
a. Connect the boards: Master Board (address
10) + NUI(0) (address 85) + 2-Zone kit slave
board (address 21) + 30AWH communicant HP
(address 2).
b. Power ON to run the AAP – Wait for 30 sec
c. Power OFF and connect the NUI(1) (address
}%$
d. Power ON to run the AAP – Wait for 30 sec
e. Power OFF and connect the NUI(2) (address
}%$
f. Power ON to run the AAP – Wait for 30 sec
g. Power OFF and connect the NUI(3) (address 88)
< &|,,}%$
h. Power ON to run the AAP – Wait for 30 sec
7. ; $&!&J@? %
units one at a time an run the AAP mode by Power ON
- Wait for 30 sec
and power OFF.
8. Check the number of devices addressed in the network
!;%©,ª %
next step.
9. Disable the AAP by setting Par.129: 0 or wait for 30
! $ %
Par.129 will turn automatically to 0.
3.3.3.3 Manual Addressing Process, MAP
^_`>;?"
Principle: This process is used to assign boards address
following network architecture given in Scheme-01 and
Q,%' ,
_>;?"
Command
Action
0
Do nothing
1
Stop Network Communications
2
J Q
3
Delete single address at Par.127
4
Reset single address at Par.127
5
Read the number of devices connected
and store it (show at Par.122)
6
J Q
communication
7
Reset all devices and delete the entire
network addresses from the database
3.3.3 Network Addressing process
Summary of Contents for 80HMA-M00
