manualshive.com logo in svg

Carrier Access Network Device Axxius 800, User Manual

Share
Download
Carrier Access Network Device Axxius 800 User Manual Download Page 477

Axxius 800 - Release 2.2

16-5

V.35/.54 Card

Card Configuration

Card Configuration

The V.35/54 card can be configured, using the Command Line Interface (CLI). 

CLI Commands

The following commands are used to configure the V.35 cards. For detailed 
information on these commands, see Chapter 5, CLI Commands.

l 

connect
Creates two-way connections between channels.

l 

disconnect
Removes a connection created by the connect command.

l 

set (v35)
Setup of channels of a V.35 card (clock, clear to send, data, equipment, line, 
receive clock invert, speed, transmit clock invert).

l 

set (v54)
Set the V.54 loopback test parameters.

l 

show (v54)
Displays the current settings for V.54 (CTS, timing, Rx clock inversion, Tx 
clock inversion, data inversion, data speed, data rate, Rx LB, Rx Addr, test 
address, Tx Prep count, Rx Prep count, test pattern, ignore ACK, loopback) 

l 

status (v54)
Displays the current near-end line status of the specified V.54 (DCD, CTS, 
DSR, RTS, DTR, BERT).

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands