manualshive.com logo in svg

Carrier Access Network Device Axxius 800, User Manual

The Axxius 800, an innovative Carrier Access Network Device, offers seamless connectivity and efficient data transmission. Enhance your user experience by easily accessing the comprehensive User Manual, available for free download from our website. Discover the full potential of this remarkable product and optimize your networking capabilities today.

Share
Download
background image

5-190

Axxius 800 - Release 2.2

CLI Commands

show

show lsprotect

The show lsprotect command displays the low speed protection information.

Syntax:

show lsprotect

Example:

show lsprotect

> SHOW lsprotect

                         Low Speed Protection Settings:

Low Speed Protection Global Service Enable: ENABLED

                             Backup Slot Settings:

                Backup Slot: 7

           Backup Slot Type: Quad T1

                             Protected Port Settings:

           SLOT:   PORT:   TYPE:        REVERSION:      PRIORITY:

           -----   -----   -----        ----------      ---------

             3       1     QT1: T1    NONREVERTIVE        1

             3       2     QT1: T1    NONREVERTIVE        1

             3       3     QT1: T1    NONREVERTIVE        1

             3       4     QT1: T1    NONREVERTIVE        1

             5       1     QT1: T1    NONREVERTIVE        2

             6       1     QT1: T1    REVERTIVE           7

             6       2     QT1: T1    REVERTIVE           7

             6       3     QT1: T1    REVERTIVE           3

             6       4     QT1: T1    REVERTIVE           7

Number of Protected Ports: 9          

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

ICP DAS USA I-7532M-FD User Manual preview
I-7532M-FD
Brand: ICP DAS USA Pages: 48
ICP DAS USA WF-2572 User Manual preview
WF-2572
Brand: ICP DAS USA Pages: 24
ICP DAS USA MSM-508 Quick Start preview
MSM-508
Brand: ICP DAS USA Pages: 4
National Instruments NI 9265 Operating Instructions Manual preview
NI 9265
Brand: National Instruments Pages: 26
National Instruments NI 9203 User Manual And Specifications preview
NI 9203
Brand: National Instruments Pages: 85
National Instruments Module SCXI-1503 User Manual preview
Module SCXI-1503
Brand: National Instruments Pages: 79
Paradyne COMSPHERE 3800 Series Release Note preview
COMSPHERE 3800 Series
Brand: Paradyne Pages: 88
Paradyne COMSPHERE 3800PLUS Supplementary Manual preview
COMSPHERE 3800PLUS
Brand: Paradyne Pages: 5
Paradyne Hotwire 6212 Quick Installation Instructions preview
Hotwire 6212
Brand: Paradyne Pages: 2
PairGain PG-FLEX RT FRL-752 Manual preview
PG-FLEX RT FRL-752
Brand: PairGain Pages: 6
NETGEAR WAG302 Installation Manual preview
WAG302
Brand: NETGEAR Pages: 2
Perle P841 Specifications preview
P841
Brand: Perle Pages: 2
Mellanox Technologies ConnectX-3 Pro MCX349A-XCCN User Manual preview
ConnectX-3 Pro MCX349A-XCCN
Brand: Mellanox Technologies Pages: 35
eWON 2101CD Installation Manual preview
2101CD
Brand: eWON Pages: 34
Westermo Ibex-RT-330-HV User Manual preview
Ibex-RT-330-HV
Brand: Westermo Pages: 34
Global Sun GL-241101 User Manual preview
GL-241101
Brand: Global Sun Pages: 39
Matrix Switch Corporation MSC-1HD1608L Product Manual preview
MSC-1HD1608L
Brand: Matrix Switch Corporation Pages: 60
Teldat G1N Installation Manual preview
G1N
Brand: Teldat Pages: 23

Brands by name

Popular brands

Load more brands