Carel Heos, User Manual

Page: 10 / 60

10
ENG
Heos +0300078EN - rel. 1.6 - 23.11.2017
2.3 16 A 1PH and 18-24 A 3PH inverter
For further details on the electrical and mechanical specifi cations, see
instruction sheet
+0500048IE
C 1
C2
L 1 /L L2/N L3 U V W
1 2 3 4 5 6 7 8 9 1 0
E
F
Fig. 2.f
Description of the terminals:
Ref. Description
L1/L, L2/N, L3
Three-phase power supply input
earth (*)
L1/L, L2/N
Single-phase power supply input
earth (*)
U, V, W
Motor output
earth (*)
C1, C2
Terminal block not used in PSD10**2**. For optional external
DC Choke in PSD10184** e PSD10244**
1,2 Relay output
3 0 V
RS485/ModBus® connection 4 Tx/Rx+
5 Tx/Rx-
6 PTC input
7 24 Vdc
Auxiliary voltage
8 0V
9 STOa
Safe Torque Off digital input (**)
10 STOb
E
PE
F (Led)
POWER (green) drive powered
RUN/FAULT (green/red) drive running / drive alarm
DATA (yellow) communication active
Tab. 2.g
(*) The earth connections inside the drive are electrically connected together and to PE.
(**) To enable the drive for operation, apply a voltage of 24 Vac/Vdc to the Safe
Torque Off digital input. The polarity is indiff erent for direct current power supply.
Coldplate with cooling adapter
The Power+ Coldplate (PSD10***A0) models are the same as respective
standard Power+ models, with the unique diff erence that the fi nned
heatsink and fan are replaced by a fl at aluminium plate.
The plate has threaded holes M5 for fi xing an additional device with
cooling function (coldplate), typically using liquid refrigerant. The
coldplate is the user’s responsibility and is not supplied by Carel.
Technical specifi cations
Operating temperature -20T60°C
Humidity <95% U.R. non-condensing
Pollution degree Max 2
Input voltage
200 - 240Vac ±10%, 50/60 Hz, 1~ (P/N PSD1***2**)
380 - 480Vac ±10%, 50/60 Hz, 3~ (P/N PSD10**4*0)
Output voltage 0 - Input voltage
Output frequency 0 - 500 Hz
Maximum length 5 m
Switching frequency 4, 6, 8 kHz
Protection functions
Drive: short-circuit, overcurrent, ground fault, over-
voltage and undervoltage, overtemperature
Motor: overtemperature and overload (150% Inom
for 1 minute)
System: Safe Torque OFF input, loss of communication
Frequency resolution 0,1 Hz
Inputs
1 motor protector input: PTC temp. probe or
voltage-free contact max source current 10mA, max.
length 25 m
Outputs 1 relay: progr. output, voltage-free contact: 240Vac, 1A
Serial input
RS485, Modbus® protocol, max trasmission speed
19200 bit/s
24 Vdc auxiliary power Double insulation, precision 10%, 50mA max
Maximum length 100m shielded cable
Index of protection IP20
Tab. 2.h
CE conformity:
2006/95/EC
EN 61800-5-1: Adjustable speed electrical power drive systems. Safety requiremen-
ts. Electrical, thermal and energy.
2004/108/EC
EN 61800-3, ed.2.0.: Adjustable speed electrical power drive systems. EMC require-
ments and specifi c test methods.
EN61000-3-2: Electromagnetic compatibility (EMC) Part 3-2: Limits for harmonic
currents (equipment connected with input current > 16 A per phase).
EN61000-3-12: Electromagnetic compatibility (EMC) Part 3-12: Limits - Limits for harmo-
nic currents (equipment connected with input current > 16 A and <= 75 A per phase).
Rated values
The table below shows the rated input and output values, as well as the
specifi cations for sizing the cables (cross-section, maximum length) and
the fuses. The values refer to an operating temperature of 60 °C and a
switching frequency of 8 kHz, unless otherwise specifi ed.
Models 16A 1PH 18A 3PH 24A 3PH
Rated input current at 230V (400V 3PH) 28 A 23 A 30 A
Fuse or type B circuit breaker 40 A 32 A 40 A
Power cable cross-section 6 mm 2 4 mm 2 6 mm 2
Rated output current 16A 18A 24A
Rated output power at 230V (400V 3PH) 6 kW 10,5 kW 14 kW
Max. total dissipation 450 W 320 W 485 W
Max. heatsink dissipation 250 W 250 W 380 W
Minimum motor cable cross-section 2,5 mm 2 4 mm 2 4 mm 2
Maximum motor cable length 5 m 5 m 5 m
Tab. 2.i
Assembly Dimensions (mm)
2
3
1
Key:
1
Coldplate cooling device (example)
2
Holes/screws for fastening the
coldplate
3 Power+ plate
Note: the air-cooled heat sink is shown in
grey in the dimensioned drawing.
26 26 75
M5
127
131
86
82
26
60
70,8
190
268 240
289,2
71,3
12
27,9 24,6
24,6
33,2
173
80
192,3
98
86
96
84
Ø 5
94
71