NOTE:
It is most important that you use the formal recorded message exactly
as it is, in the event that it is received by the Triple Zero Services. Also we
recommend that you change the combination code of your Key Safe lock if it
has been disclosed via your recorded message to any outside sources. This is
to protect your own security. Your recorded message will need to be updated
with the NEW combination Key Safe code after any change that may occur.
STEP 7.
Check how well your message was recorded by pressing
STAr (
*
) 7
and listening via the phone handset. If you are not satisfied
with the message you can repeat Step 6 again.
STEP 8. VIEWING YOUR STORED PHONE NUMBERS.
You are able to view the phone numbers in the order that you have stored
them through the Smart Dialler indication window. It is important that
you check these numbers to ensure that they are correct. Preceding
each number will be the prefix P1, P2, P3 etc indicating Phone number
1, 2, 3, etc.
To view them press star 8
(of course the “Function” switch on the rear
of the Smart Dialler is still over on “SET”).
Your numbers will be displayed in sequential order in the indication
window on the top of the Dialler. These numbers are also verbalised
through the telephone handset.
STEP 9.
Connecting the Dialler rechargeable battery.
Turn off the
power to the dialler. Remove the screw to the cover plate beneath
the dialler using the small Phillips head screwdriver provided in the
pack. It should be noted that the Smart Dialler will continue to operate
normally without a battery; however should there be a power failure
then the battery is relied upon to ensure that the Smart Dialler will
continue to operate for up to 10 hours or longer. A warning message
stating:
“Mains power is not detected”
will sound once the battery has
been installed if the power supply is not connected or turned on at the
switch.
It is now time to turn the power back on.
STEP 10.
Connect the dialler to the Telephone Jack. Using the phone
cable provided, plug one end into the Smart Dialler Jack labelled “LINE”
and the other end into the wall phone socket. Make sure that the cable
clicks into position. You can tidy up all the cables upon completion of
installation.
STEP 6.
rECOrDING
the
VOICE MESSAGE
Using
STAr (
*
) 6
You have a maximum of
45 seconds
in which to record one of the
following messages.
OPTION 1.
“This is (Name) of (full address including state) and I have pressed my CareAlert
button and need emergency help. Press the star key on your phone to speak to
me – if I do not respond, please take action to ensure my well-being. Should this
message reach Emergency Services please connect this call to the Ambulance.
Repeating, my name is (name) and my address is (address). This message is
played twice. Press the star key now to speak to me.
OPTION 2: (THIS IS ONLY USED IF YOU HAVE AN OUTDOOR KEYSAFE)
“This is (Name) of (full address including state) and I have pressed my CareAlert
button and need emergency help. Press the star key on your phone to speak to
me – if I do not respond, please take action to ensure my well-being. My Key
Safe Lock is located (say location) and the opening code is (give combination).
Should this message reach Emergency Services please connect this call to the
Ambulance. Repeating, my name is (name) and my address is (address). This
message is played twice. Press the star key now to speak to me”
Both of these message options can be read within 45 seconds. Option
2 may need to be read at a faster pace. Anyone can record this message
on behalf of the owner of the CareAlert Smart Dialler.
(Note: The CareAlert Smart Dialler, will commence playing CareAlert’s Message
followed by your message within a few seconds of dialing. This is to satisfy
ALL Australian and International “Pick up” signals. Therefore when testing
your Smart Dialler, you may notice that the receiver of the emergency call
could answer part way through your message. This is quite normal and this is
why the message is repeated).
To record your personal message, press STAr (
*
) 6
and after the
immediate beep, begin speaking your message clearly into the phone.
At the conclusion immediately press the
“#” Key
to stop recording
and you will hear two beeps. If the two beeps sound before you finish,
your message is too long and will need to be said a little quicker.
(Your
message can be changed at any time by repeating the above procedures)
9
8
