Canon iPF6100 - imagePROGRAF Color Inkjet Printer Service Manual Download Page 16

Page: 16 / 367

Chapter 1

1-4

1.2.3 Ink Tank

0013-0608

The ink tank is disposable.

There are twelve pigment-based ink colors (matte black,black,photo cyan,cyan,photo

magenta,magenta,yellow,red,blue,green,gray,and photo gray).

This printer features a mechanism by which only the correct color ink tank will fit in the given slot.

When the message No Ink is displayed, replace the ink tank with a new one. Also, each ink tank should generally

be replaced six months after you have opened the package.

F-1-4

1.2.4 Cutter

0013-3524

A round-blade cuter comes with the cutter unit.

F-1-5

1.2.5 Roll Feed Unit

0013-2512

Roll Feed Unit

The roll feed unit is optionally available to use roll media with this printer.

F-1-6

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer















































































































































































































































































































































































Search results

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer

Reviews:

Related manuals for iPF6100 - imagePROGRAF Color Inkjet Printer

Brands by name

Popular brands

Canon iPF6100 - imagePROGRAF Color Inkjet Printer, Service Manual

Search results

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer

Reviews:

Related manuals for iPF6100 - imagePROGRAF Color Inkjet Printer

Brands by name

Popular brands