Canon iPF6100 - imagePROGRAF Color Inkjet Printer Service Manual Download Page 242

Page: 242 / 367

Chapter 4

4-70

b) Adjusting the wire roller

To prevent the wire roller mounted on the carriage from contacting the duct and others during carriage operation,

perform the following adjusutment whenever tou have removed or replaced the carriage unit. This adjustment

is not required when you have replaced only the multi sensor.

* Make adjustments with the carriage lock released.

* Make adjustments with the tube disconnected from the tube guide.

1) Remove the ink tube from the wire guide.

2) Loosen the two screws[1]

3) Turn the gear[2] until the lift cam flag[3] reaches the position shown below.

* Bottom position where the sensor[4] light is blocked by the flag (lowest position to which the carriage unit

descends)

F-4-115

[1]

[2]

[3]

[4]

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer















































































































































































































































































































































































Search results

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer

Reviews:

Related manuals for iPF6100 - imagePROGRAF Color Inkjet Printer

Brands by name

Popular brands

Canon iPF6100 - imagePROGRAF Color Inkjet Printer, Service Manual

Search results

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer

Reviews:

Related manuals for iPF6100 - imagePROGRAF Color Inkjet Printer

Brands by name

Popular brands