manualshive.com logo in svg

Canon iPF6100 - imagePROGRAF Color Inkjet Printer, Service Manual

The Canon iPF6100 is a high-performance imagePROGRAF color inkjet printer. For easy servicing and efficient troubleshooting, a comprehensive Service Manual is available for download, completely free of charge. Find the manual at manualshive.com, offering step-by-step instructions to ensure optimal performance and longevity for your printer.

Share
Download
background image

Chapter 2  

2-38

2.3.2.6 Maintenance Cartridge

2.3.2.6.1 Maintenance cartridge

0013-4161

a) Maintenance cartridge 

The maintenance cartridge can contain up to approximately 957 ml (approx. 1021 g ) of waste ink (including

the moisture evaporation in the waste ink).

b) Detection of waste ink in maintenance cartridge

The quantity of waste ink in the maintenance cartridge is measured by counting dots.  

When the quantity of waste ink collected in the maintenance cartridge reaches 80% of the cartridge capacity, a

warning message "MTCart Full Soon" appears to indicate that the maintenance cartridge is nearly full. 

If printing is continued, an error message "Maint Cartridge Replace Cart"

 

appears to indicate that the

maintenance cartridge is full. 

When this error occurs, the printer judges the maintenance cartridge as being full of waste ink and stops printing

immediately. The printer stops even if printing is in progress, and it will not operate until the maintenance

cartridge is replaced with a new one.

The maintenance cartridge incorporates an EEPROM. The main controller reads and writes the contents of the

EEPROM to control the maintenance cartridge status.

F-2-19

Maintenance Cartridge

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer
















































































































































































































































































































































































Reviews:

No comments

Related manuals for iPF6100 - imagePROGRAF Color Inkjet Printer

Samsung SPP 2020 - Photo Printer - 20 Sheets Manual Del Usuario preview
SPP 2020 - Photo Printer - 20 Sheets
Brand: Samsung Pages: 81
Samsung ML-6000 Bedienungsanleitung preview
ML-6000
Brand: Samsung Pages: 98
Samsung ML-4050N Compatibility Manual preview
ML-4050N
Brand: Samsung Pages: 6
Samsung ML-3750ND User Manual preview
ML-3750ND
Brand: Samsung Pages: 203
Samsung ML-3312ND Manual Del Usuario preview
ML-3312ND
Brand: Samsung Pages: 264
Samsung ML-2165W/XAA Manual Del Usuario preview
ML-2165W/XAA
Brand: Samsung Pages: 228
Samsung ML-2165 User Manual preview
ML-2165
Brand: Samsung Pages: 211
Samsung ML-2525 Brochure & Specs preview
ML-2525
Brand: Samsung Pages: 5
Samsung ML-1865W Manual Del Usuario preview
ML-1865W
Brand: Samsung Pages: 92
Samsung ML-1865W User Manual preview
ML-1865W
Brand: Samsung Pages: 75
Samsung ML-6060 Technical Instructions preview
ML-6060
Brand: Samsung Pages: 11
Samsung ML-1450 Series Manual Del Usuario preview
ML-1450 Series
Brand: Samsung Pages: 206
Samsung ML 3050 - B/W Laser Printer Manual Del Usuario preview
ML 3050 - B/W Laser Printer
Brand: Samsung Pages: 103
Samsung ML 3050 - B/W Laser Printer User Manual preview
ML 3050 - B/W Laser Printer
Brand: Samsung Pages: 215
Samsung ML-1450 Series Quick Manual preview
ML-1450 Series
Brand: Samsung Pages: 2
Samsung CLP 510N - Color Laser Printer User Manual preview
CLP 510N - Color Laser Printer
Brand: Samsung Pages: 266
Samsung 550N - CLP Color Laser Printer Manual De Instalación preview
550N - CLP Color Laser Printer
Brand: Samsung Pages: 296
Samsung CLP-415NW User Manual preview
CLP-415NW
Brand: Samsung Pages: 276

Brands by name

Popular brands

Load more brands