manualshive.com logo in svg

Canon iPF6100 - imagePROGRAF Color Inkjet Printer, Service Manual

The Canon iPF6100 is a high-performance imagePROGRAF color inkjet printer. For easy servicing and efficient troubleshooting, a comprehensive Service Manual is available for download, completely free of charge. Find the manual at manualshive.com, offering step-by-step instructions to ensure optimal performance and longevity for your printer.

Share
Download
background image

Chapter 4

4-23

4.3.7 Carriage Unit

0016-8499

a) Removeing the carriage unit

1) Drain the ink. 

Refer to DISASSEMBLY/REASSEMBLY > Points to Note on Disassembly and Reassembly > Draining the

Ink.

2) Turn off the power, and then move the carriage over the platen. 

Refer to DISASSEMBLY/REASSEMBLY > Points to Note on Disassembly and Reassembly > Opening the

Cap/Moving the Wiper Unit.

3) Remove the printhead.

4) Remove the joint of the ink tube unit. Wrap the removed joint with a plastic bag or other covering so that ink

does not splashes, then close the plastic bag.

F-4-40

5) Remove the linear scale[1] from the right clamp plate's spring, and then remove it rightward.

F-4-41

When removing the linear scale, take care not to damage or stain it. The stained or damaged liner plate can cause

malfunction.

[1]

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer
















































































































































































































































































































































































Reviews:

No comments

Related manuals for iPF6100 - imagePROGRAF Color Inkjet Printer

F+D Feinwerk- und Drucktechnik Plus Software Manual preview
Plus
Brand: F+D Feinwerk- und Drucktechnik Pages: 41
TallyGenicom 9022 Brochure & Specs preview
9022
Brand: TallyGenicom Pages: 3
Lanier LD360 Brochure & Specs preview
LD360
Brand: Lanier Pages: 6
Xerox WorkCentre 4265 Quick Use Manual preview
WorkCentre 4265
Brand: Xerox Pages: 20
Xerox Phaser 6120 Instructions Manual preview
Phaser 6120
Brand: Xerox Pages: 11
Canon Pixma TS7700i Series Manual preview
Pixma TS7700i Series
Brand: Canon Pages: 554
Ricoh D096 Service Manual preview
D096
Brand: Ricoh Pages: 268
Xerox WorkCentre 7328 Brochure & Specs preview
WorkCentre 7328
Brand: Xerox Pages: 8
3D Systems ProJet x60 Series User Manual preview
ProJet x60 Series
Brand: 3D Systems Pages: 72
Oki OKIPAGE 10e Setup Manual preview
OKIPAGE 10e
Brand: Oki Pages: 20
idp SMART-30S User Manual preview
SMART-30S
Brand: idp Pages: 88
EFI Pro 32r Operation Manual preview
Pro 32r
Brand: EFI Pages: 168
Oki F0305 User Manual preview
F0305
Brand: Oki Pages: 188
MIMAKI UJF-605R II Daily Care Manual preview
UJF-605R II
Brand: MIMAKI Pages: 28
Cashino CSN-58III User Manual preview
CSN-58III
Brand: Cashino Pages: 61
Xerox 6360V_DN Brochure preview
6360V_DN
Brand: Xerox Pages: 4
Epson XP-220 Network Manual preview
XP-220
Brand: Epson Pages: 35
Epson WorkForce WF-7610 Quick Manual preview
WorkForce WF-7610
Brand: Epson Pages: 16

Brands by name

Popular brands

Load more brands