Canon iPF6100 - imagePROGRAF Color Inkjet Printer Service Manual Download Page 192

Page: 192 / 367

Chapter 4

4-20

4.3.6 Cutter

0016-8468

a) Removing the cutter unit

1) When removing the cutter unit, open the top cover, and then remove the roll feed unit, output guide, left and

right circle covers, tank cover, left front cover, right upper cover, operation panel, exhaust filter, lower rear

cover, right cover, right front cover, upper front cover, lower front cover.

Refer to DISASSEMBLY/

REASSEMBLY > Points to note on Disassembly and Reassembly > External Covers.

2) Turning motor pulley[1] in the arrow direction, move cutter[2] about 2 cm to the right of the leftmost end.

F-4-35

[1]

[2]

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer















































































































































































































































































































































































Search results

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer

Reviews:

Related manuals for iPF6100 - imagePROGRAF Color Inkjet Printer

Brands by name

Popular brands

Canon iPF6100 - imagePROGRAF Color Inkjet Printer, Service Manual

Search results

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer

Reviews:

Related manuals for iPF6100 - imagePROGRAF Color Inkjet Printer

Brands by name

Popular brands