background image

Stationary

Air Compressor

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.

Description

Air compressor units are intended to
provide compressed air to power
pneumatic tools and operate spray guns.
The pumps supplied are oil lubricated. A
small amount of oil carryover is present
in the compressed air stream.
Applications requiring air free of oil or
water should have the appropriate filter
installed. The air compressor unit must
be mounted as described in the
instructions on a solid floor. Any other
use of these units will void the warranty
and the manufacturer will not be
responsible for problems or damages
resulting from such misuse.

Safety Guidelines

This manual contains information that is
very important to know and understand.
This information is provided for SAFETY
and to PREVENT EQUIPMENT PROBLEMS.
To help recognize this information,
observe the following symbols. 

Danger indicates 
an imminently

hazardous situation which, if not
avoided, will result in death or serious
injury.

Warning indicates 

a potentially

hazardous situation which, if not
avoided, could result in death or
serious injury.

Caution indicates a 
potentially

hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.

Notice indicates 

important

information, that if not followed, may
cause damage to equipment.

Unpacking

After unpacking the unit, inspect
carefully for any damage that may have
occurred during transit. Make sure to

NOTICE

!

CAUTION

!

WARNING

!

DANGER

Operating Instructions 

Vertical Models

tighten fittings, bolts, etc., before
putting unit into service.

Do not operate 
unit if damaged

during shipping, handling or use.
Damage may result in bursting and
cause injury or property damage.

General Safety

Since the air compressor and other
components (material pump, spray
guns, filters, lubricators, hoses, etc.)
used, make up a high pressure
pumping system, the following safety
precautions must be observed at all
times:

1. Read all manuals

included with this
product carefully. Be
thoroughly familiar
with the controls and
the proper use of the equipment.

2. Follow all local electrical and safety

codes as well as in the United
States, the National Electrical Codes
(NEC) and Occupational Safety and
Health Act (OSHA).

!

WARNING

IN227706AV  2/11

© 2011

Breathable Air Warning

This compressor/pump is NOT
equipped and should NOT be used
“as is” to supply breathing quality
air. For any application of air for
human consumption, you must fit
the air compressor/pump with
suitable in-line safety and alarm
equipment. This additional
equipment is necessary to properly
filter and purify the air to meet
minimal specifications for Grade D
breathing as described in
Compressed Gas Association
Commodity Specification G 7.1 -
1966, OSHA 29 CFR 1910. 134,
and/or Canadian Standards
Associations (CSA).

DISCLAIMER OF WARRANTIES
In the event the compressor is used
for the purpose of breathing air
application and proper in-line
safety and alarm equipment is not
simultaneously used, existing
warranties are void, and Campbell
Hausfeld disclaims any liability
whatsoever for any loss, personal
injury or damage.

!

DANGER

3. Only persons well acquainted with

these rules of safe operation should
be allowed to use the compressor.

4. Keep visitors away and NEVER allow

children in the work area.

5. Wear safety glasses and

use hearing protection
when operating the
unit.

6. Do not stand on or use the unit as 

a handhold.

7. Before each use, inspect compressed

air system and electrical
components for signs of damage, 

MANUAL

Figure 1

REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.

See Warranty on page 8 for important information about commercial use of this product.

Summary of Contents for Vertical

























Reviews: