background image

5

Zero output from receptacles

Low output voltage 

6 Vac or above

with no load

Below 6 Vac

High output voltage with no load

Low output voltage under load

Erratic output voltage

Noisy operation

Engine won’t start

1. Engine speed is too slow
2. Open or shorted wiring

3. Faulty capacitor
4. Open/shorted rotor or stator windings

5. Open rectifier

1. Engine speed is too slow
2. Open rectifier
3. Faulty capacitor
4. Open/shorted rotor or stator windings

1. Generator head not magnetized

1. Faulty capacitor
2. Engine speed is too fast

1. Open rectifier
2. Engine speed too slow at full load
3. Excessive load applied

1. Dirty, corroded, or loose wiring

connection

2. Unbalanced load applied

1. Loose generator or engine bolt
2. Short circuit in generator field or load

3. Faulty bearing

1. No fuel.
2. Fuel switch is in closed position.
3. Engine switch is in closed position.
4. Spark plug dirty or wrong gap

5. Not enough compression inside the

cylinder

1. Adjust engine speed 

2. Clean and reconnect all wiring 

3. Replace capacitor 

4. Test winding resistance, replace winding

if necessary 

5. Test rectifier, replace if necessary 

1. Adjust engine speed 

2. Test rectifier, replace if necessary 

3. Replace capacitor 

4. Test winding resistance, replace winding

if necessary 

1. Re-magnetize generator head 

1. Replace capacitor 

2. Adjust engine speed 

1. Test rectifier, replace if necessary 

2. Adjust engine speed 

3. Reduce the applied load

1. Referring to the wiring diagram, clean

and reconnect all wiring 

2. Remove all loads, then apply each one

individually to determine which one is
causing erratic function

1. Tighten all mountings
2. Test winding resistance, replace field

winding if necessary

Test load devices for shorts. Replace
defective load device.

3. Replace bearing

1. Check fuel. 
2. Place fuel switch in open position.
3. Place engine switch in open position.
4. Clean spark plug. Adjust gap. (See page 3)

Replace if necessary.

5. Check leakage from the cylinder

These diagnostic and repair procedures should be performed by an authorized service center.

Troubleshooting Chart

  Symptom                                                              Possible Cause(s)                                                     Corrective Action

Model GN1200 

 Model

GN 1200

GENERATOR

Type

Single-Phase, Brushless

Voltage

120 V

Frequency

60 Hz

Maximum Output

1500 W

Rated Out put

1100 W

ENGINE

Type

1-cylinder, 4-stroke, forced air cooling gasoline engine

Displacement

87 cc

Maximum Output

3.0 HP/ 4000 rpm

Fuel

Unleaded Gasoline

UNIT

Oil Capacity

400 ml

Fuel tank capacity

5.5 L

Dimensions (L x W x H)

430 x 310 x 370 mm

Noise Level @ 7 m

68 dB (A)

Net Weight

25 kg

Specifications

Summary of Contents for GN1200





















Reviews: