![background image](http://html1.mh-extra.com/html/calpeda/70020030000/70020030000_operating-instructions-manual_485124012.webp)
GB
Page 12 / 64
CT,T, TP, Rev24 - Operating Instructions
It is forbidden to execute any operations with
the direct use of hands. Use water-resistant,
anti-cut gloves to disassemble and clean or in
other particular cases.
i
During maintenance operations external
personnel is not allowed.
Maintenance operations that are not described in
this manual must be made only by special personnel
authorized by Calpeda S.p.A.
For further technical information regarding the use or
the maintenance of the device, contact Calpeda S.p.A.
8.1. Routine maintenance
OFF
Before every maintenance operations
disconnect the power supply and make sure
that the device could not accidentally operate.
When the pump remains inactive it must be
emptied completely if there is a risk of freezing.
Remove the front cover (12.00) or the drain plug
(14.12), if available, to empty the pumps
of the T, TP series. To empty completely the CT pumps,
remove the pump and turn it upside-down.
After a long idle period, before restarting the unit,
check that the impeller is not jammed because of
incrustations, settling solids (deposit formation)
or other causes. If necessary clean with suitable
action.
8.2. Dismantling the system
Close the suction and delivery gate valves and drain
the pump casing before dismantling the pump.
8.3. Dismantling the pump
OFF
Close the suction and delivery gate valves before
dismantling.
For dismantling and re-assembly see construction in
the cross section drawing.
To remove the impeller (28.00) T, TP use the threaded
dismantling holes.
9. DISPOSAL
OFF
Tίά зΣΕΠ ΘόsΥΤsΕΠ Τέ tίά ΘάvόΗά Ρust bά ΘΤΣά bγ
specialized company.
Make sure the specialized company follows the
ΗΠΕssόзΗΕtόΤΣ Τέ tίά ΡΕtάΧόΕΠ ΥΕΧts έΤΧ tίά sάΥΕΧΕtόΤΣ.
Observe the local regulations and dispose the device
accordingly with the international rules for environment
protection.
10. SPARE PARTS
10.1.
Spare-parts request
WίάΣ ΤΧΘάΧόΣή sΥΕΧά ΥΕΧts, ΥΠάΕsά ΦuΤtά tίάόΧ
designation, position number in the cross section
drawing and rated data from the pump name plate
(type, date and serial number).
The spare parts request shall be sent to CALPEDA
S.p.A. by phone, fax, e-mail.
11. ESIGNATION OF PARTS
Nr. Designation
12.00 Casing cover
12.20 Screw
14.00 Pump casing
14.04 PΠuή (зΠΠόΣή)
14.12 Plug (draining)
14.20 O-ring
14.24 Screw
28.00 Impeller
28.20 Impeller key
32.00 Lantern bracket
36.00 Mechanical seal
36.50 Shoulder ring
36.52 Shoulder ring
46.00 DάиάΗtΤΧ
70.00 Lantern bracket
70.18 Screw
73.00 Pump-side bearing
73.12 Circlip
76.00 Motor casing with winding
76.04 Cable gland
76.16 Support
76.35 Cover
76.54 Terminal box, set
78.00 Shaft with rotor packet
81.00 Fan-side bearing
81.08 Circlip
82.00 Motor end shield, fan side
82.04 Compensating spring
82.08 Screw
88.00 Motor fan
90.00 Fan cover
90.04 Screw
92.00 Tie-bolt
94.00 Capacitor
94.02 Capacitor gland
98.00 Terminal box cover
98.04 Screw
98.08 Gasket
99.00 Motor, complete
Changes reserved.
www.calpeda.su
www.calpeda.su