background image

BYD e6A AUTO Owner's Manual

 

1-16 Doors and Keys 

Keys

 

 

Intelligent Keys and Mechanical Keys 

1. Intelligent Key - used to open/lock all doors 

and available in two types: electronic 

intelligent key and card-type intelligent key. 

Electronic intelligent key can be used to 

open/lock doors, make an emergency 

alarm and search for the car at a distance. 

2. Mechanical key (in electronic intelligent key 

and car-type intelligent key) - is used to 

open/lock doors and trunk. 

 

 

    WARNING 

 

People with heart pacemakers and 
defibrillators must be kept away from the 
antenna of intelligent access and starting 
system, as the electromagnetic wave 
may affect normal use of these devices. 
For information on the position of the 
antenna, please refer to "Antenna 
Position" in this section. 

  Drivers with heart pacemakers and 

defibrillators and people using other 
medical electronic devices must ask 
manufacturer about the dangers of 
interference to these device posed by 
electromagnetic waves. Electromagnetic 
wave may cause unexpected results to 
these devices.

 

  

NOTE 

Pay attention to the following items when 
using intelligent keys: 

 

Do not attach any object which may 
block electromagnetic waves (such as 
a metal container) to the key. 

 

Do not knock the key forcibly on other 
projects. 
 

 

Do not place the intelligent key in high 
temperature, direct sunlight or on 
motor hood for a long time. 

 

Do not clean the key in water or an 
ultrasonic washer. 

 

Do not put the intelligent key near any 
device which may produce 
electromagnetic wave, such as a cell 
phone.

 

 

 

Using the Mechanical Key inside the 

Electronic Intelligent Key

 

To use mechanical key in electronic intelligent 

key, pull down the switch to release the key as 

shown in the figure. Make sure to put back the 

mechanical key after use. 

Summary of Contents for e6A




































































































































































































Reviews: