BYD e6A Owner'S Manual Download Page 169

Page: 169 / 195

BYD e6A AUTO Owner's Manual

Motor and Chassis 5-9

Check the breather tubes on the transmission

frequently to ensure the normal performance

of these components.

If BYD original transmission fluid is not

available, you can use API certified gear oil

as substitute. For specific specifications,

please refer to Maintenance Manual or

contact BYD authorized service station.

Transmission fluid shall be replaced by

mileage or interval as specified in Periodic

Maintenance Table. The existing transmission

fluid shall be drained completely before filling

new transmission fluid.

Please contact BYD authorized service

station if you have any doubt about checking

fluid level or filling fluid inbox.

Maintenance for rear drive
transmission (if equipped)

After running in a new transmission, drain the

lubricant in the transmission case. Unscrew

the drain plug1 to drain the lubricant and

tighten it again. Then unscrew the filler plug 2

to refill fresh lubricant. ATF220 is

recommended to use. Please keep the filling

amount at about 1.5 L. It is recommended to

replace lubricant at the specified service

station.

Pay attention to check the lubricant amount in

the transmission case during daily operation.

Remove the filler plug, and touch the fluid

level in the plug hole. The normal level should

be up to the edge of the plug hole.

Otherwise,

please refill fresh oil approved by BYD until it

over flows from the filler opening. Then screw

the filler plug and tighten it

Replace the

lubricant in the transmission case regularly.

To secure the quality of lubricant, wash and

clean the transmission case before replacing

lubricant.

Check the bolts outside of the transmission

for looseness or absence during daily

operation. If a bolt is found loose, tighten it

timely; if there is any bolt missing, reinstall it.

Keep the bolts and transmission case clean in

order to facilitate heat dissipation.

Check the components of vent ducts on the

transmission frequently to ensure the normal

performance of these components.

Summary of Contents for e6A




































































































































































































Search results

Summary of Contents for e6A

Reviews:

Related manuals for e6A

Brands by name

Popular brands

BYD e6A, Owner'S Manual

Search results

Summary of Contents for e6A

Reviews:

Related manuals for e6A

Brands by name

Popular brands