background image

Other dangers 

 

Butzbach GmbH Industrietore  

 

Originalbedienungsanleitung SPACELITE_V1 

 

24/02/2021  

 

9

 

3.3 

Other risks during service and maintenance work 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Warning! Risk of injury from unexpected opening of the door!

 

 

The door system could open unexpectedly on its own or be opened by other people. 

Always remain aware when you are in the door area. 

Do not lean any ladders against the door.  

Warning! Injuries and damage when working on the system!

 

 

Risk of injury and risk of damage. 

Make  sure  that  electricity  has  been  disconnected  from  the  control  unit  when  working  on  the 

system. 

Ensure that the main power switch is guarded against being turned back on without authorisation 

with a hanging lock and that the plug is guarded against being plugged in. 

If multiple people are working on the system, 

each one

 must ensure that the main power switch 

is secured against being turned on without authorisation. 

Warning! Comply with the regulations, otherwise there is a risk 

of injury!

 

 

When working on the system, always heed the legal regulations and safety notices, otherwise there is a 

risk of injury! 

Comply with the general legal regulations (safety, accident prevention, VDE standards) as well as 

these safety notices. 

The system may only be operated by authorised personnel who are familiar with its operation. 

If the operator of the system does not have full visibility during operation, the operator must take 

appropriate measures to ensure operational safety. 

Always perform work on the system with sure footing! 

Do not wear loose clothing, jewellery, etc. when working on the system. They can be grabbed by 

moving parts. 

When  working  on  the  system,  wear  protective  gloves,  safety  shoes,  a  protective  helmet  and 

protective goggles when performing machining activities.  

In principal, avoid stopping in the door area. 

Before operating the door system, ensure that no people or objects are located in the door area. 

Hanging on and going for a ride during door movement is strictly forbidden! 

Summary of Contents for SPACELITE HT150














































Reviews: