Brother PR-600 Manual Download Page 139

Page: 139 / 227

Editing the Embroidery Pattern (Pattern Editing Screen)

121

Touch the keys to adjust the pattern to the
desired size.

Each touch of a key slightly enlarges or reduces
the pattern.

The size of the pattern is displayed after a key
is touched to change it.

Vertical length

Horizontal length

• The size that the pattern can be enlarged

depending on the pattern or character.

• Depending on the pattern or character, if it is

rotated 90 degrees it may be enlarged even
more.

• If the pattern is rotated, the vertical and

horizontal directions may be reversed.

• To return the pattern to its original size,

touch

so that it changes to

If necessary, touch the arrow keys to adjust
the position of the pattern.

For more details, refer to page 119.

After making the desired changes, touch

The pattern editing screen appears again.

Rotating a pattern

The pattern can be rotated between 1 and 359
degrees either clockwise or counterclockwise.

Touch .

The screen shown below appears.

●

After changing the size of the pattern,
check the icons for the embroidery
frames that can be used and use only the
indicated frames. If a frame other than
those indicated are used, the presser foot
may hit the embroidery frame and cause
injuries.

CAUTION

Example: Original angle

Rotates 90 degrees to the left

Rotates 10 degrees to the left

Rotates 1 degree to the left

Rotates 90 degrees to the right

Rotates 10 degrees to the right

Rotates 1 degree to the right

Touch this key to return the pattern to its original
angle.

Moves the pattern in the direction of the arrow on
the key.

Touch this key to close this screen.

Sapphire.book Page 121 Friday, August 1, 2003 9:12 AM

Summary of Contents for PR-600




































































































































































































































Search results

Summary of Contents for PR-600

Reviews:

Related manuals for PR-600

Brands by name

Popular brands

Brother PR-600, Manual

Search results

Summary of Contents for PR-600

Reviews:

Related manuals for PR-600

Brands by name

Popular brands