Brother PR-600 Manual Download Page 36 | Manualshive

Page: 36 / 227

background image

EMBROIDERING TUTORIAL

———————————————————————————————————————————————————

18

1. Installing the Bobbin

The bobbin case is loaded with a bobbin wound with embroidery bobbin thread. Remove the bobbin case with

the bobbin, check the amount of thread remaining in the bobbin, and then re-install the bobbin case with the
bobbin. For precautions concerning the bobbin, refer to page 15.

Note

●

A function that shows the amount of bobbin
thread remaining is not available with this

machine. Before starting to embroider, be
sure to check the certain amount of bobbin

thread remaining.

●

Make sure to clean the bobbin case every

time when change the bobbin. For details
on cleaning the bobbin case, refer to

“Cleaning the bobbin case” on page 185.

Removing the bobbin case

1

Open the hook cover.

Pull the hook cover toward you.

2

Pull the thread picker toward you.

1

Thread Picker

To gain access to the bobbin case easily, pull
the thread picker toward front.

Note

●

Thread picker is a device that is used to
hold the thread when begining to sew or

when trimming the thread.

3

Grab the bobbin case latch, and remove the
bobbin case.

1

Latch

4

Close the latch, and then remove the bobbin
from the bobbin case.

1

Bobbin

5

Check the amount of bobbin thread remaining.

■

Oiling the machine

After removing the bobbin case, apply oil to the
machine. The race should be oiled. For details on
oiling the machine, refer to “Oiling the machine”
on page 186.

Note

●

Make sure to oil the race of hook everyday
when use the machine.

●

The thread picker can only be moved

within a certain range. Do not pull it with
extreme force.

1

CAUTION

1

1

Sapphire.book Page 18 Friday, August 1, 2003 9:12 AM

«
...
34
35
36
37
38
...
»

Summary of Contents for PR-600




































































































































































































































Reviews:

No comments

Related manuals for PR-600

Brand: Dakota Digital Pages: 38

Brand: Janome Pages: 30

Brand: Oki Pages: 2

Brand: Wallenstein Pages: 48

Brand: RADEMACHER Pages: 48

Brand: IAG Pages: 3

Brand: iArmor Pages: 6

Brand: ZEPP Pages: 36

FleetMaster Air FW8 Series

Brand: SAF-HOLLAND Pages: 20

STRONGARM RVR303

Brand: Blue Giant Pages: 48

Brand: Celestron Pages: 24

Brand: Kasanova Pages: 22

Brand: Graphite Pages: 44

1501-3120-6010-100

Brand: S+S Regeltechnik Pages: 16

Brand: echoflex Pages: 8

Brand: Kargo Master Pages: 6

CombiCool CAB-40B

Brand: Waeco Pages: 136

Brand: CASTLECREEK Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands