Brother PR-600 Manual Download Page 27

Page: 27 / 227

Setting Up the Machine

Adjusting the operation panel
position

Adjust the orientation and angle of the operation
panel so it can easily be operated.

Loosen the thumb screw to bring the
operation panel forward.

Thumb screw

Adjust the operation panel to an easy-to-
operate position, and then tighten the thumb
screw.

Adjust the orientation of the operation panel.

Loosen the thumb screw, adjust the operation
panel to an easy-to-view orientation, and then
tighten the thumb screw.

Thumb screw

Adjust the angle of the operation panel.

Loosen the thumb screw, adjust the operation
panel to an easy-to-view angle, and then
tighten the thumb screw.

Thumb screw

Note

●

Using the disc-shaped screwdriver
included, loosen and firmly tighten the
thumb screw.

Sapphire.book Page 9 Friday, August 1, 2003 9:12 AM

Summary of Contents for PR-600




































































































































































































































Search results

Summary of Contents for PR-600

Reviews:

Related manuals for PR-600

Brands by name

Popular brands

Brother PR-600, Manual

Search results

Summary of Contents for PR-600

Reviews:

Related manuals for PR-600

Brands by name

Popular brands