Brother PR-600 Manual Download Page 219

Page: 219 / 227

Troubleshooting

201

The installed embroidery frame

is too small.

Check which embroidery

frames can be used, and then
install a larger embroidery

frame. (Refer to page 28.)

The embroidery data cannot be

detected.

The embroidery data may be

damaged.

Embroidery data with an

incompatible version is being
used.

Embroidery data that is not
complete or has an unknown

version cannot be used.

Characters have been com-

bined until they extend out of
the embroidery frame.

Decrease the number of charac-
ters so that they fit within the

embroidery frame.

Sewing cannot begin from the

specified starting position.

Change the starting position or

move the frame and change the
embroidering position. (Refer to

page 87.)

Another operation was per-

formed while the automatic
needle-threading mechanism

was threading the needle.

Press the automatic needle

threading button, and then per-
form the other operation after

the needle is threaded. (Refer to
page 39.)

Thread color that was specified

is incorrect.

The thread color number that

was entered is not in the custom
thread table setting. Check the

number, and then try entering
the number again.

Six manual needle bar settings

were being specified.

No more than five needle bars

can be specified.

Sapphire.book Page 201 Friday, August 1, 2003 9:12 AM

Summary of Contents for PR-600




































































































































































































































Search results

Summary of Contents for PR-600

Reviews:

Related manuals for PR-600

Brands by name

Popular brands

Brother PR-600, Manual

Search results

Summary of Contents for PR-600

Reviews:

Related manuals for PR-600

Brands by name

Popular brands