Brother PR-600 Manual Download Page 80

Page: 80 / 227

OTHER BASIC PROCEDURES

——————————————————————————————————————————————————

As shown in the illustration, press

to extend

the needle-mounting clamp

. Attach the

clamp to the needle, and then release the
pressed area to clamp the needle. To unclamp
the needle, press

again.

While holding the needle in place with your
left hand, tighten the needle set screw.

Use the allen screw driver to turn the needle
set screw clockwise.

●

Be sure to insert the needle all the way
up until it touches the needle bar stopper
and securely tighten the needle set screw
with the allen screw driver, otherwise the
needle may break or the machine may be
damaged.

CAUTION

Sapphire.book Page 62 Friday, August 1, 2003 9:12 AM

Summary of Contents for PR-600




































































































































































































































Search results

Summary of Contents for PR-600

Reviews:

Related manuals for PR-600

Brands by name

Popular brands

Brother PR-600, Manual

Search results

Summary of Contents for PR-600

Reviews:

Related manuals for PR-600

Brands by name

Popular brands