Brother PR-600 Manual Download Page 111 | Manualshive

Page: 111 / 227

background image

Temporary Needle Bar Setting

93

4

Memo

●

The thread color (needle bar) change
specified as described above only applies
until the next color change. If the pattern
contains another area with the same color
or when the same pattern is sewn the next
time, the area is sewn with the original
color.

●

The thread color (needle bar) can be
changed with this procedure even when the
machine has been stopped with a specified
pause or at the time of spool change.

●

If the start/stop button was pressed to stop
the machine while an area was being sewn,
a temporary needle bar setting cannot be
applied. The thread color (needle bar)
cannot be changed in the middle of an area
that is being sewn.

Sapphire.book Page 93 Friday, August 1, 2003 9:12 AM

«
...
109
110
111
112
113
...
»

Summary of Contents for PR-600




































































































































































































































Reviews:

No comments

Related manuals for PR-600

Brand: Samsung Pages: 7

Brand: Barco Pages: 2

Brand: Barco Pages: 22

Brand: Fellowes Pages: 4

Brand: Obelink Pages: 2

Brand: Fellowes Pages: 7

Brand: Fellowes Pages: 8

Brand: Fellowes Pages: 8

Brand: FeiYu Tech Pages: 5

Brand: FEIYUTECH Pages: 19

Brand: FeiYu Tech Pages: 25

Brand: FEIYUTECH Pages: 16

HOIST-A-TOP JL CRANK

Brand: Lange Originals Pages: 13

Brand: LAS Pages: 44

Brand: LAS Pages: 24

Brand: OFFCARR Pages: 12

Brand: OEM Tools Pages: 4

Brand: VTech Baby Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands