manualshive.com logo in svg

Brocade Communications Systems FastIron, Administration Manual, Page: 107 / 388

Share
Download
Brocade Communications Systems FastIron Administration Manual Download Page 107

Uploading a primary or secondary boot image from an IPv6 TFTP server

For example, to upload a primary or secondary boot image from an IPv6 TFTP server to a device flash
memory, enter a command such as the following.

device#copy tftp 2001:DB8:e0ff:7837::3 primary.img flash primary

This command uploads the primary boot image named primary.img from a TFTP server with the IPv6
address of 2001:DB8:e0ff:7837::3 to the device primary storage location in flash memory.

Syntax:copy tftp ipv6-address source-file-name flash primary 

| 

secondary

The 

tftp ipv6-address

 parameter specifies the address of the TFTP server. You must specify this

address in hexadecimal using 16-bit values between colons as documented in RFC 2373.

The 

source-file-name

 parameter specifies the name of the file you want to copy from the TFTP server.

The 

primary

 keyword specifies the primary location in flash memory, while the 

secondary

 keyword

specifies the secondary location in flash memory.

Uploading a running or startup configuration from an IPv6 TFTP server

For example to upload a running or startup configuration from an IPv6 TFTP server to a device, enter a
command such as the following.

device#copy tftp 2001:DB8:e0ff:7837::3 newrun.cfg running-config

This command uploads a file named newrun.cfg from a TFTP server with the IPv6 address of
2001:DB8:e0ff:7837::3 to the device.

Syntax:copy

 

tftp ipv6-address source-file-name

 

running-config

|

startup-config

The 

tftp ipv6-address

 parameter specifies the address of the TFTP server. You must specify this

address in hexadecimal using 16-bit values between colons as documented in RFC 2373.

The 

source-file-name

 parameter specifies the name of the file you want to copy from the TFTP server.

Specify the 

running-config

 keyword to upload the specified file from the IPv6 TFTP server to the

device. The device copies the specified file into the current running configuration but does not overwrite
the current configuration.

Specify the 

startup-config

 keyword to upload the specified file from the IPv6 TFTP server to the

device. The the device copies the specified file into the current startup configuration but does not
overwrite the current configuration.

Using SNMP to save and load configuration information

You can use a third-party SNMP management application such as HP OpenView to save and load a
configuration on a Brocade device. To save and load configuration information using HP OpenView, use
the following procedure.

NOTE

The syntax shown in this section assumes that you have installed HP OpenView in the "/usr" directory.

1. Configure a read-write community string on the Brocade device, if one is not already configured. To

configure a read-write community string, enter the following command from the global CONFIG level
of the CLI.

snmp-server community

 

string ro

|

rw

Uploading a primary or secondary boot image from an IPv6 TFTP server

FastIron Ethernet Switch Administration Guide

107

53-1003625-01

Summary of Contents for FastIron





































































































































































































































































































































































































Reviews:

No comments