Service Manual 04/2010 Rev.B
99
Fig.212
Mount the lip seal (Fig.213).
IMPORTANT!
INSTALL THE LIP SEAL WITH THE RING SIDE
TOWARDS THE OUTER SIDE OF THE
FLANGE.
Fig.213
Install the plastic ring (Fig.214).
Fig.214
Install the dustproof seal (Fig.215).
Fig.215
Grease the cylinder and piston seals and
mount the piston by using rubber hammer.
Install the rear flange
6.5.
Turn on the machine.
Open and close the chuck cylinder and verify
if it works fine and there is any oil leaking.
Close the chuck cylinder and mount the cross
#4 and the spacer (Fig.207).
Open the chuck cylinder ‘till end of the stroke.
Mount the cross #3 and tighten the nut #2
FIRMLY.
Install the protections #1 (Fig.207).
6.17 TOOL HOLDER CYLINDER:
CHECK AND REPLACEMENT
:
1h
:
End wrenches 19,22,24 and 30mm, 6 and
8mm Allen wrenches, 13mm tube type
wrench, rubber hammers, manometer, green
loctite, hydraulic containers oil.
L
:
Defective chuck cylinder may cause the
following malfunctions:
1. Slow or locked tool holder movement.
2. Oil
leaking.
IMPORTANT!
BEFORE STARTING WITH ANY DISMOUNTING
OPERATION, VERIFY IF THE MAXIMUM
HYDRAULIC PRESSURE IS CORRECTLY
REGULATED
6.4.
NOTE: THE REPLACEMENT OF THE WHOLE
CYLINDER IS ONLY SUGGESTED IN CASE OF
MECHANICAL DEFECTS.
TO CHECK THE CYLINDER:
Install the manometer on the cylinder (
6.4
Fig.142).
Switch the machine on.
In case of slow movement, move to left the
tool holder by keeping it clamped: during the
movement verify that the hydraulic pressure
Summary of Contents for KING 5600
